Cypher/FRSkyInput - Revision history

FlexTeam: /* FRSky Transmitter settings: */

2021-09-22T18:53:18Z

‎FRSky Transmitter settings:

2021-09-22T18:51:48Z

‎Setup for using a FRSky Tx/Rx

2021-09-22T18:51:07Z

‎Travel

2019-09-20T21:29:55Z

‎FRSky Transmitter settings:

2019-09-06T14:40:53Z

‎Travel

2019-09-06T14:40:39Z

‎Travel

2019-08-12T18:56:05Z

‎Receiver Page

2019-08-12T18:55:35Z

‎FRSky Transmitter settings:

2019-08-12T18:55:02Z

‎Travel

2019-08-11T18:30:00Z

‎Travel

@@ Line 31: / Line 31: @@
 === FRSky Transmitter settings: ===
 <br />
-'''<big>This page is under construction and is not considered 'confirmed' at this time. Do all command/control checks in the manual. Expert users please provide feedback to support@flexinnovations.com</big>'''<br />
+'''<big>Do all command/control checks in the manual. Expert users please provide feedback to support@flexinnovations.com</big>'''<br />
 <br />
 ----

@@ Line 1: / Line 1: @@
-== '''Setup for using a FRSky Tx/Rx''' ==
+== '''Setup for using a FRSky or OpenTx Tx/Rx''' ==
 <br />
 '''<big>Always start with a reset/new transmitter model!</big>'''

@@ Line 79: / Line 79: @@
 ==== Travel ====
 [[File:BF_RX_Notes.png|thumb|upright=0.42|right|Betaflight Travel Tune Notes]]
 <pre>
-    Throttle           +-97%   These all need validation on Rx page
+    Throttle           98% High, 96% Low
-    Aileron            +-97%
+    Aileron            +-98%
-    Elevator           +-97%
+    Elevator           +-98%
-    Rudder             +-97%
+    Rudder             +-98%
-    Profile-Stab       +-97%
+    Profile-Stab       +-98%
     Config-Tilt        +85 -55%  To Start - MUST adjust with gauges!
 </pre>
 :'''NOTE:''' Go to the Receiver Page in Configurator and fine tune Aileron, Elevator, and Rudder travel to 1000-1500-2000. (See notes on top of Configurator page)
 <br />
 ==== Timers ====
 <pre>

@@ Line 65: / Line 65: @@
 Significant Subtrim should not be required. (can set center to 1500 on receiver page)
 </pre><br />
 ==== Reversing ====
 <pre>
@@ Line 78: / Line 77: @@
 :'''NOTE'''‡: The internal Flex pilots set the CH6 switch UP/Back for forward flight and Low/Front for Hover. You can set per your preference.
 <br />
 ==== Travel ====
 [[File:BF_RX_Notes.png|thumb|upright=0.42|right|Betaflight Travel Tune Notes]]
@@ Line 91: / Line 88: @@
 </pre>
 :'''NOTE:''' Go to the Receiver Page in Configurator and fine tune Aileron, Elevator, and Rudder travel to 1000-1500-2000. (See notes on top of Configurator page)
-<br /><br />
+<br />
-−
 ==== Timers ====
 <pre>

@@ Line 90: / Line 90: @@
     Config-Tilt        +85 -55%  To Start - MUST adjust with gauges!
 </pre>
-:'''NOTE:''' Go to the Receiver Page in Configurator and fine tune Aileron,Elevator, and Rudder travel to 1000-1500-2000. (See notes on top of Configurator page)
+:'''NOTE:''' Go to the Receiver Page in Configurator and fine tune Aileron, Elevator, and Rudder travel to 1000-1500-2000. (See notes on top of Configurator page)
 <br /><br />

@@ Line 24: / Line 24: @@
 Channel Order            ->  AETR1234  (When Tx order is set to AETR)
 </pre>
 :'''SAVE''' the page!
 <br /><br />
 ----

@@ Line 46: / Line 46: @@
 ----
 <br />
-:'''NOTE:''' Use a Receiver with diversity and SBUS out capability recommended.<br />
+:'''NOTE:''' Use a Receiver with diversity and SBUS out capability.<br />
 :'''NOTE:''' You should verify the completed settings using the tools using the BetaFlight Receiver page.
 <br />

@@ Line 88: / Line 88: @@
     Rudder             +-97%
     Profile-Stab       +-97%
-    Config-Tilt        +97 -60%  To Start-Must adjust with gauges!
+    Config-Tilt        +85 -55%  To Start - Must adjust with gauges!
 </pre>
 :Go to the Receiver Page in Configurator and fine tune Aileron,Elevator, and Rudder travel to 1000-1500-2000. (See notes on top of Configurator page)