Cypher/JRDMSSInput - Revision history

FlexTeam: /* Travel */

2019-09-20T21:20:25Z

‎Travel

2019-09-20T21:19:13Z

‎Travel

2019-09-20T21:17:44Z

‎Setup

2019-09-10T16:40:39Z

‎CLI Page

2019-09-06T14:25:29Z

‎Setup for using a JR DMSS Tx/Rx

2019-09-06T14:24:26Z

‎Travel

2019-09-06T14:23:36Z

‎Travel

2019-09-06T14:23:09Z

‎Travel

2019-09-06T14:21:29Z

‎Reversing

2019-09-06T14:19:56Z

‎CLI Page

@@ Line 83: / Line 83: @@
     Channel 7          +-91%     Spare channel as needed (ex. throttle arm)
 </pre>
-:'''NOTE:''' Go to the Receiver Page in Configurator and fine tune Aileron,Elevator, and Rudder travel to 1000-1500-2000. (See notes on top of Configurator page)
+:'''NOTE:''' Go to the Receiver Page in Configurator and fine tune Aileron,Elevator, and Rudder travel to 1000-1500-2000. (See notes on top of Configurator page), You can also tune the throttle to 1000 to 2000 with the trimmer set in the middle.
 <br />

@@ Line 81: / Line 81: @@
     Profile-Stab       +-91%
     Config-Tilt        +70 -45%  To Start - MUST adjust with gauges!
-    Channel 7          +-91%     Spare channel as needed
+    Channel 7          +-91%     Spare channel as needed (ex. throttle arm)
 </pre>
 :'''NOTE:''' Go to the Receiver Page in Configurator and fine tune Aileron,Elevator, and Rudder travel to 1000-1500-2000. (See notes on top of Configurator page)

@@ Line 56: / Line 56: @@
 Bind your Transmitter and Receiver
 In Transmitter menu, X.BUS FUNCTION, set  BUS TYPE : MODE.B
-(FYI, this will disabled your Rx servo ports)
+(FYI, this will disable your Rx servo ports)
 </pre><br />

@@ Line 21: / Line 21: @@
 ==== CLI Page ====
 <pre>
-Channel Order            ->  AER2T134  Must be set in CLI Mode for JR DMSS!
+Channel Order         ->  AER2T134 Must be set in CLI Mode when using JR DMSS!
 To set, in your configurator, go to the 'CLI' page.
@@ Line 32: / Line 32: @@
     save
-Hit ENTER on the keyboard. (This is NOT the the same as 'Save to File' button)
+Hit ENTER on the keyboard.
 </pre>
 :NOTE: You can VERIFY (but not pick) the rather unique AER2T134 settings on the Receiver Page.

@@ Line 5: / Line 5: @@
 :'''NOTE:''' If your JR transmitter is DMSS, continue here. If it is DSM2 or DSMX, follow the Spektrum instructions!
 :'''NOTE:''' You will use the 3-Pin to 4-Pin Male to Male cable provided to connect the JR DMSS Rx's XBUS to the FLEXF3. This is the same cable arrangement shown on page 15 of the manual for the Futaba connections. (Non-Telemetry)
 <br /><br />
 ----

@@ Line 73: / Line 73: @@
 [[File:BF_RX_Notes.png|thumb|upright=0.42|right|Betaflight Travel Tune Notes]]
 <pre>
-    Throttle           +-91%    ???? Verify from Tx
+    Throttle           +-91%    Fine tune on the BF Configurator's Receivers page
     Aileron            +-91%
     Elevator           +-91%
     Rudder             +-91%
     Profile-Stab       +-91%
-    Config-Tilt        +70 -45%  To Start-Must adjust with gauges!
+    Config-Tilt        +70 -45%  To Start - Must adjust with gauges!
     Channel 7          +-91%     Spare channel as needed
 </pre>

@@ Line 67: / Line 67: @@
 </pre>
 :'''NOTE:'''† You must verify these settings via the rotating body on the configurator receiver page.
-:'''NOTE'''‡: The internal Flex pilots set the CH6 switch UP/Back for forward flight and Low/Front for Hover. You can set per your preference.
+:'''NOTE:'''‡ The internal Flex pilots set the CH6 switch UP/Back for forward flight and Low/Front for Hover. You can set per your preference.
 <br />