Cypher/JetiInput - Revision history

FlexTeam: /* JETI Transmitter settings: */

2019-09-10T16:36:19Z

‎JETI Transmitter settings:

2019-09-06T14:27:03Z

‎Setup for using a Jeti Tx/Rx

2019-09-06T14:26:52Z

‎Setup for using a Jeti Tx/Rx

2019-09-06T14:13:35Z

‎JETI Transmitter settings:

2019-09-06T14:12:52Z

‎JETI Transmitter settings:

2019-09-06T14:11:41Z

‎JETI Transmitter settings:

2019-09-06T14:11:30Z

‎JETI Transmitter settings:

2019-09-06T14:09:20Z

‎JETI Transmitter settings:

2019-08-12T18:54:03Z

‎JETI Transmitter settings:

2019-08-12T18:52:28Z

‎JETI Transmitter settings:

@@ Line 101: / Line 101: @@
   NO  ‡
   YES †    Or as user prefers for Stability/ANGLE MODE
-  NO  §
+  NO  §    Or as user prefers for Configuration/Fan Tilt
   NO  †
   NO  †

@@ Line 5: / Line 5: @@
 '''<big>Always start with a reset/new transmitter model!</big>'''
 <br />
-'''NOTE:''' You will use the 3-Pin to 4-Pin Male to Male cable provided to connect the Jeti Rx to the FLEXF3. This is the same cable arrangement shown on page 15 of the manual for the Futaba connections. (Non-Telemetry)
+:'''NOTE:''' You will use the 3-Pin to 4-Pin Male to Male cable provided to connect the Jeti Rx to the FLEXF3. This is the same cable arrangement shown on page 15 of the manual for the Futaba connections. (Non-Telemetry)
 :These instructions supplement the printed manual. Please read the manual before proceeding.
 <br /><br />

@@ Line 5: / Line 5: @@
 '''<big>Always start with a reset/new transmitter model!</big>'''
 <br />
-NOTE: You will use the 3-Pin to 4-Pin Male to Male cable provided to connect the Jeti Rx to the FLEXF3. This is the same cable arrangement shown on page 15 of the manual for the Futaba connections. (Non-Telemetry)
+'''NOTE:''' You will use the 3-Pin to 4-Pin Male to Male cable provided to connect the Jeti Rx to the FLEXF3. This is the same cable arrangement shown on page 15 of the manual for the Futaba connections. (Non-Telemetry)
 <br /><br />
 ----

@@ Line 64: / Line 64: @@
    R Slider       -P5   -optional-not currently used-drives spare servo port on FLEXF3)
   L Slider       -P6   -optional-not currently used-drives spare servo port on FLEXF3)
-</pre><big>'''NOTE:''' '''do NOT'''''Italic text'' hit the Auto-Assign button!</big>
+</pre><big>'''NOTE:''' '''''do NOT''''' hit the Auto-Assign button!</big>
 <br />
 ''<big>Model->Servo Assignment</big>''

@@ Line 64: / Line 64: @@
    R Slider       -P5   -optional-not currently used-drives spare servo port on FLEXF3)
   L Slider       -P6   -optional-not currently used-drives spare servo port on FLEXF3)
-</pre><big>'''NOTE:''' do not hit the Auto-Assign button!</big>
+</pre><big>'''NOTE:''' '''do NOT'''''Italic text'' hit the Auto-Assign button!</big>
 <br />
 ''<big>Model->Servo Assignment</big>''

@@ Line 33: / Line 33: @@
 :DS-16 Mode 2 transmitter and R3 EX RSW Receiver used for validations
 :(Most common models expected to work the SAME)<br />
-As always, start with a freshly '''RESET''' transmitter model.
+:As always, start with a freshly '''RESET''' transmitter model.
 :You can verify the completed settings using the tools using the BetaFlight Configurator Receiver page.
 <br /><br />

@@ Line 108: / Line 108: @@
 :'''NOTE:'''‡ You must check Aileron, Elevator, Rudder 'Reversing' by rotating the virtual 'body' on the Receiver Page of the Configurator
 :'''NOTE:'''§ The internal Flex pilots set the CH6 switch UP/Back for forward flight and Low/Front for Hover. You can set per your preference.
-:'''Do the command and gyro checks'''<br />
+:'''Do the command and gyro checks in the manual'''
-:When finished, you can go to the configurator's Receiver tab and verify the AER 'direction' by using the transmitter to 'rotate' the body on the screen.<br />
-:You can go to the configurator's Receiver Page and check/fine tune the Aileron, Elevator, and Rudder travels per Notes.
 <br /><br />
 ''<big>Model->Timers/Sensors</big>''

@@ Line 84: / Line 84: @@
 <pre>
 All items set to defaults except as noted
-ALL subtrims 0%             (defaults)<br />
+ALL subtrims 0%             (defaults)
 Travels                     -general
     All Max Positive  100%   -except for the Config/Tilt noted below     (defaults)
@@ Line 90: / Line 91: @@
 Travel for Config/Tilt
     Max Positive      81%    -start with these and then you MUST adjust final angle w/gauges
-    Max Negative     -57%<br />
+    Max Negative     -57%
 Reversing                    1-10 in Servo Assignment order as just above