F-100D 90mm EDF/LatestUpdates - Revision history

FlexTeam: /* Spektrum SRXL2 Use */

2020-09-28T14:03:56Z

‎Spektrum SRXL2 Use

2020-09-17T23:48:34Z

‎Addendums

2020-09-17T23:47:37Z

‎Care Tips

2020-09-17T23:45:41Z

‎ESC Wires

2020-09-17T23:44:43Z

‎Addendums

2020-09-17T23:40:08Z

‎Care Tips

2020-09-04T13:05:16Z

‎Latest Updates

2020-09-03T12:07:43Z

‎Build Tips

2020-09-03T12:06:25Z

‎Build Tips

2020-09-03T12:06:03Z

‎Build Tips

@@ Line 27: / Line 27: @@
 ====Spektrum SRXL2 Use====
-*Note that the AR6600T using SRXL2 is working with the Aura and F-100D. More information can be found in the [[Aura#Radio_Brand_Tips_-_for_all_Auras| '''Aura Brand Tips''']]
+*Note that the AR6610T using SRXL2 is working with the Aura and F-100D. More information can be found in the [[Aura#Radio_Brand_Tips_-_for_all_Auras| '''Aura Brand Tips''']]
 == Build Tips ==

@@ Line 6: / Line 6: @@
 * This version matches the printed manual.
-=== Addendums ===
+=== Addendums and Additional Info===
 ====Center of Gravity====
 *The CG section of the F-100D manual had some conflicting information displayed. The correct CG's are listed in the image to the right. Click for the full sized image.

@@ Line 15: / Line 15: @@
 ====Care Tips====
 *As with all foam planes, and especially those with dark colors and cockpits, keep your plane out of direct sunlight (or cover it) when not flying!
-*TIP: You can use a small drill bit or a #11 knife blade to make a small 2-3mm hole in the clear canopy above the ejection seat. This will reduce the temperatures a bit in the cockpit due to the 'greenhouse effect'.
+*TIP: You can use a small drill bit or a #11 knife blade to make a small 2-3mm hole in the clear canopy above the ejection seat. This will reduce the temperatures a bit in the cockpit due to the 'greenhouse effect'. Hot cars and direct Sun are also bad for the finish.
 *Use foam, a soft stand, or towels, or similar items to protect your models surface and finish when working on it, or transporting it!

@@ Line 10: / Line 10: @@
 *The CG section of the F-100D manual had some conflicting information displayed. The correct CG's are listed in the image to the right. Click for the full sized image.
 ====ESC Wires====
-*Check that the 3 ESC/Motor wires are fully plugged in. We recommend securing them with heat shrink or electrical tape to remove any chance they could be pulled loose.
+*Check that the 3 ESC/Motor wires are fully plugged in before installing the Fin.
 ====Care Tips====
 *As with all foam planes, and especially those with dark colors and cockpits, keep your plane out of direct sunlight (or cover it) when not flying!

@@ Line 9: / Line 9: @@
 ====Center of Gravity====
 *The CG section of the F-100D manual had some conflicting information displayed. The correct CG's are listed in the image to the right. Click for the full sized image.
 ====Care Tips====
 *As with all foam planes, and especially those with dark colors and cockpits, keep your plane out of direct sunlight (or cover it) when not flying!

@@ Line 23: / Line 23: @@
 *The Drop Tanks are fully assembled, no need to assemble the fins onto the tanks.
-[[/F-100D_90mm_EDF| '''CLICK HERE to go back to the main F-100D Wiki Page''']]
+[[F-100D_90mm_EDF| '''CLICK HERE to go back to the main F-100D Wiki Page''']]
 <noinclude>