FlexJetTV/LatestUpdates - Revision history

FlexTeam: /* Addendum */

2019-03-21T13:36:30Z

‎Addendum

2019-03-21T13:35:49Z

‎Printed Manual Typo

2019-03-21T13:34:08Z

‎Full Build Video

2019-03-21T13:33:39Z

‎Full Build Video

2019-03-21T13:32:46Z

‎Initial Build

2019-03-21T13:31:50Z

‎Printed Manual Typo

2019-03-21T13:30:39Z

‎Printed Manual Typo

2019-03-21T13:29:29Z

2019-03-21T13:28:46Z

‎Printed Manual Typo

2019-03-06T19:10:46Z

@@ Line 75: / Line 75: @@
 == Addendum ==
-See Retract Sequencer, Fairing Attachment, and other notes. -Above-
+See Fin Tube, Retract Sequencer, Fairing Attachment, and other notes. -Above-
 == Parts Notes ==

@@ Line 7: / Line 7: @@
 * Simply plug the fin into the fuselage and attach it with the screw
 -or-
-* Glue the fin tube into the fuselage. (this would require breaking and shaving the fin off of the fin tube should it ever require replacement).
+* Glue the fin tube into the fuselage. (this would require breaking and shaving the fin off of the fin tube should the fin ever require replacement).
 See below for general tips

@@ Line 40: / Line 40: @@
 <br />
 Note: This is for the normal Flexjet, but nearly all of the covered areas still apply.
 <br />
 '''Timeline for specific segments of this video!'''<br />

@@ Line 39: / Line 39: @@
 [https://www.youtube.com/watch?v=JTJxbuKcS1I '''Click to view the Full Build Instructional Video on YouTube''']
 <br />
+Note: This is for the normal Flexjet, but nearly all of the covered areas still apply.
 '''Timeline for specific segments of this video!'''<br />
 (Go to YouTube Page and you will have links)<br />

@@ Line 31: / Line 31: @@
 *Your '''Side Fairings''' behind the stab are likely NOT installed (change to prevent shipping damage). They are likely packed with your missile rails. Please glue them onto the aft fuselage with CA or Epoxy before installing the tail cone.
 *Please check the glue joints of the '''Rib''' in the fuselage socket where the wing attaches. Add some medium CA as needed. There have been several reports of inadequate glue.
-*When re-installing the '''Tailpipe''', a good technique is to get the tailpipe aligned with the back edge of the fan as close as possible, then 'pop' the aft end of the tailpipe with the open palm of your hand and it will 'jump' forward into place.
 [https://www.youtube.com/watch?v=dIjrTTspdAA '''Click to view a Stab/Tailpipe Instructional Video on YouTube''']

@@ Line 4: / Line 4: @@
 === Printed Manual Typo ===
-The Fin Tube is glued into the fin at the factory. You may proceed on one of two paths:
+The '''Fin Tube''' is glued into the fin at the factory. You may proceed on one of two paths:
 -Simply plug the fin into the fuselage and attach it with the screw
 -or-

@@ Line 20: / Line 20: @@
 {{#ev:youtube|https://www.youtube.com/watch?v=dIjrTTspdAA|360|right|Stab/Tailpipe Video}}
 [[File:Stab Link 5022.jpg|thumb|upright=0.5|right|Linkage Installation]]
-*When using the new '''Spektrum "T" Spektrum Receivers''' such as the AR8010T, AR9030T, etc. the Aura needs to be '''Firmware 1.6''' to establish connection via SRXL as noted on our AR8010T page.
+*When using the new '''Spektrum "T" Spektrum Receivers''' such as the AR8010T, AR9030T, etc. the Aura needs to be '''Firmware 1.6''' (it ships with a higher version) to establish connection via SRXL as noted on our AR8010T page.
 **The AR8010T is our highest recommended Spektrum Receiver for the FlexJet TV.
 *For '''Futaba''' users, our highest recommended ''FASST'' receiver is the R7008SB or R6303SB. For ''FHSS'', the R2008SB.
@@ Line 35: / Line 35: @@
 ----
 === Full Build Video ===
 [https://www.youtube.com/watch?v=JTJxbuKcS1I '''Click to view the Full Build Instructional Video on YouTube''']

@@ Line 3: / Line 3: @@
 == Latest Updates ==
 === Printed Manual Typo ===
-None - See below
 === Latest Online Manual ===

@@ Line 6: / Line 6: @@
 === Latest Online Manual ===
-The Latest Version of the [http://resources.flexinnovations.com/Flex_Images/PDF_Library/Flex%20Jet%20Manual%20EN%20V1.0.pdf '''FlexJet TV Manual (Rev - 1.0)'''] is available online.
+The Latest Version of the [http://resources.flexinnovations.com/Flex_Images/PDF_Library/FlexJet_TV_Manual_V1.0.pdf '''FlexJet TV Manual (Rev - 1.0)'''] is available online.
 * This version matches the printed manual. (See add-in note on Gear Travel below)
 * See Build Tips below for minor updates.