WikiSys at 19:46, 2 July 2023

2023-07-02T19:46:53Z

WikiSys: Created page with "{{DISPLAYTITLE:How to Setup your Transmitter for the RV-8 70cc with Aura}} FORCETOC == Transmitt..."

2023-07-02T17:38:37Z

Created page with "{{DISPLAYTITLE:How to Setup your Transmitter for the RV-8 70cc with Aura}} __FORCETOC__  == Transmitt..."

New page

{{DISPLAYTITLE:How to Setup your Transmitter for the RV-8 70cc with Aura}}
__FORCETOC__ 
== Transmitter Model Setup Procedure ==
# Create a Blank Transmitter Airplane Model with 1 Throttle, 1 Aileron, 1 Elevator, 1 Rudder and any Flaps or Flap System OFF.
# Assign the Transmitter's Ch5/Gear channel to a 3 Position switch to change the Flight Modes in flight
# Assign the Transmitter's CH6/Aux1 Channel to a 3 Position switch to control the Flaps in flight
# Assign the Transmitter's Ch7/Aux2 Channel to a 2 Position switch to function as a Gyro Gain Kill switch in flight
#* The Gyro Gain Kill functionality is Enabled by default when creating the Aura Config File, but can be Disabled.
# Adjust Aileron, Elevator, Rudder and Throttle End Points (aka Travel Limits or ATV) as shown in the table below for your Transmitter brand
# Verify the rest of the settings as shown in the table below for your Transmitter brand

{| class="wikitable" style="text-align: center"
|+ RV-8 70cc Transmitter Setup
!style="width: 40%" | !!style="width: 20%" | Spektrum, Futaba, JR & Graupner !!style="width: 20%" | FrSky !!style="width: 20%" | Jeti (EX-Bus)
|-
| '''Wing/Tail Type''' || 1 Aileron, 1 Elevator, 1 Rudder || 1 Aileron, 1 Elevator, 1 Rudder || 1 Aileron, 1 Elevator, 1 Rudder
|-
| '''End Points (Travel Adjust or ATV)''' || Ail/Ele/Rud: 125%|| Ail/Ele/Rud: 100% || Ail/Ele/Rud: 100%
|-
| '''Reversing''' ||colspan=3 | Not Allowed
|-
| '''Sub-Trim''' || colspan=3 | Verify at Zero, NOT ALLOWED
|-
| '''Trim Levers''' || colspan=3 | Verify at Zero
|-
| '''Flight Mode Switch: CH5/Gear''' || colspan=3 | Assign the CH5/Gear channel to a 3 Position switch
|-
| '''Flap Switch: CH6/Aux1''' || colspan=3 | Assign the CH6/Aux1 channel to a 3 Position switch<br>Do NOT use Transmitter Flap System. Flap Values are pre-programmed into the Aura.
|-
| '''Gyro Gain Kill Switch: CH7/Aux2**'''|| colspan=3 | Assign the CH7/Aux2 channel to a 2 Position switch (Optional)
|}

'''<nowiki> ** </nowiki>''' - The Gyro Gain Kill Switch is initially Enabled in the Aura Config Tool Wizard but can be Disabled.

<noinclude>
[[Category:SuperPNP|Super PNP]]
[[Category:RV8|RV-8]]
</noinclude>

@@ Line 2: / Line 2: @@
 __FORCETOC__ <!-- This forces the Table of Contents since it has less than 3 levels -->
 == Transmitter Model Setup Procedure ==
-# Create a Blank Transmitter Airplane Model with 1 Throttle, 1 Aileron, 1 Elevator, 1 Rudder and any Flaps or Flap System OFF.
+# Create a Blank Transmitter Airplane Model with 1 Throttle, 1 Aileron, 1 Elevator, 1 Rudder
 # Assign the Transmitter's Ch5/Gear channel to a 3 Position switch to change the Flight Modes in flight
 # Assign the Transmitter's CH6/Aux1 Channel to a 3 Position switch to control the Flaps in flight
@@ Line 27: / Line 28: @@
 | '''Flight Mode Switch: CH5/Gear''' || colspan=3 | Assign the CH5/Gear channel to a 3 Position switch
 |-
-| '''Flap Switch: CH6/Aux1''' || colspan=3 | Assign the CH6/Aux1 channel to a 3 Position switch<br>Do NOT use Transmitter Flap System.  Flap Values are pre-programmed into the Aura.
+| '''Flap Switch: CH6/Aux1''' || colspan=3 | Assign the CH6/Aux1 channel to a 3 Position switch<br>Do NOT use Transmitter Flap System.<br>Flap Values, Flap to Elevator Mixes, and Flap Speed are pre-programmed into the Aura.
 |-
 | '''Gyro Gain Kill Switch: CH7/Aux2**'''|| colspan=3 | Assign the CH7/Aux2 channel to a 2 Position switch (Optional)

RV-8 70cc/TransmitterSetup - Revision history

WikiSys at 19:46, 2 July 2023

WikiSys: Created page with "{{DISPLAYTITLE:How to Setup your Transmitter for the RV-8 70cc with Aura}} __FORCETOC__ == Transmitt..."

WikiSys: Created page with "{{DISPLAYTITLE:How to Setup your Transmitter for the RV-8 70cc with Aura}} FORCETOC == Transmitt..."