Difference between revisions of "Cypher/JRDMSSInput"
From Flex Innovations Wiki
(→Travel) |
(→Reversing) |
||
Line 58: | Line 58: | ||
==== Reversing ==== | ==== Reversing ==== | ||
<pre> | <pre> | ||
− | 1 Throttle | + | 1 Throttle N |
− | 2 Aileron | + | 2 Aileron R (Reversed) |
− | + | 3 Elevator N | |
− | 4 Rudder | + | 4 Rudder R (Reversed) |
5 Gear N -or as desired | 5 Gear N -or as desired | ||
− | 6 Aux1 | + | 6 Flap/Aux1 N -or as desired |
</pre> | </pre> | ||
+ | :'''NOTE:''' You must verify these settings via the rotating body on the configurator receiver page. | ||
<br /> | <br /> | ||
+ | |||
==== Travel ==== | ==== Travel ==== | ||
[[File:BF_RX_Notes.png|thumb|upright=0.42|right|Betaflight Travel Tune Notes]] | [[File:BF_RX_Notes.png|thumb|upright=0.42|right|Betaflight Travel Tune Notes]] |
Revision as of 18:24, 12 August 2019
Contents
Setup for using a JR DMSS Tx/Rx
- Always start with a reset/new transmitter model!
- NOTE: If your JR transmitter is DMSS, continue here. If it is DSM2 or DSMX, follow the Spektrum instructions!
- NOTE: You will use the 3-Pin to 4-Pin Male to Male cable provided to connect the JR DMSS Rx to the FLEXF3. This is the same cable arrangement shown on page 15 of the manual for the Futaba connections. (Non-Telemetry)
CYPHER/Betaflight Settings
- Use one of the Betaflight configuration tools to make these settings. Be sure to SAVE the configuration page after adjustments.
Configuration Page
Receiver Mode -> Serial Based Receiver (Cypher Default) Serial Receiver Provider -> XBUS_MODE_B (aka JR XBUS MODE B) Telemetry slider -> OFF (Cypher Default)
- SAVE the page!
CLI Page
Channel Order -> AER2T134 Must be set in CLI Mode for JR DMSS! To set, in your configurator, go to the 'CLI' page. Cut and paste or type the following line into the command line: map AER2T134 Hit ENTER on the keyboard than paste or type: save Hit ENTER on the keyboard. (This is NOT the 'Save to File' button)
- You can VERIFY (but not pick) the rather unique AER2T134 settings on the Receiver Page.
JR DMSS Transmitter settings:
- XG14 Mode 2 transmitter and R731BX and R712BX Receivers used for validations. Choose a receiver with diversity and capable of JR XBUS MODE B.
- (Most common models expected to work the SAME)
- You can verify the completed settings using the tools using the BetaFlight Receiver page.
Setup
Name: Cypher Model Type: Plane/Acro Wing type: 1 Ail, 0 Flaps (default) Tail type: Normal 1 Elev 1 Rudd (default) Throttles: 1 (default) The rest are defaults (default) Assign a 2-position switch to CH5/Gear (Stability/Angle Mode) Assign a 3-position switch to CH6/Aux1 (Configuration/Tilt) Bind your Transmitter and Receiver In Transmitter menu, set Rx Output to JR Mode B (FYI, this will disabled your Rx servo ports)
Reversing
1 Throttle N 2 Aileron R (Reversed) 3 Elevator N 4 Rudder R (Reversed) 5 Gear N -or as desired 6 Flap/Aux1 N -or as desired
- NOTE: You must verify these settings via the rotating body on the configurator receiver page.
Travel
1 Throttle +-91% ???? Verify from Tx 2 Aileron +-91% 3 Elevator +-91% 4 Rudder +-91% 5 Profile-Stab +-91% 6 Config-Tilt +70 -45% To Start-Must adjust with gauges! 7 Channel 7 +-91% Spare channel as needed
- Go to the Receiver Page in Configurator and fine tune Aileron,Elevator, and Rudder travel to 1000-1500-2000. (See notes on top of Configurator page)
Timers
Set a count down Timer length suggestion for first flights 2200mAh: 2:30 2600mAh: 3:10 3300mAh: 4:00