Difference between revisions of "Cypher/FRSkyInput"
(Created page with "== '''Setup for using a Graupner HOTT Tx/Rx''' == <br /> '''<big>Always start with a reset/new transmitter model!</big>''' <br /> NOTE: You will use the 3-Pin to 4-Pin Male to...") |
(→Setup for using a Graupner HOTT Tx/Rx) |
||
| Line 1: | Line 1: | ||
| − | == '''Setup for using a | + | == '''Setup for using a FR Sky Tx/Rx''' == |
<br /> | <br /> | ||
'''<big>Always start with a reset/new transmitter model!</big>''' | '''<big>Always start with a reset/new transmitter model!</big>''' | ||
<br /> | <br /> | ||
| − | NOTE: You will use the 3-Pin to 4-Pin Male to Male cable provided to connect the | + | NOTE: You will use the 3-Pin to 4-Pin Male to Male cable provided to connect the FR Sky Rx to the FLEXF3. This is the same cable arrangement shown on page 15 of the manual for the Futaba connections. (Non-Telemetry) |
<br /><br /> | <br /><br /> | ||
---- | ---- | ||
| Line 14: | Line 14: | ||
<pre> | <pre> | ||
Receiver Mode -> Serial Based Receiver (Cypher Default) | Receiver Mode -> Serial Based Receiver (Cypher Default) | ||
| − | Serial Receiver Provider -> | + | Serial Receiver Provider -> SBUS |
Telemetry slider -> OFF (Cypher Default) | Telemetry slider -> OFF (Cypher Default) | ||
</pre> | </pre> | ||
| Line 22: | Line 22: | ||
Should be same as out of box, but you can check! | Should be same as out of box, but you can check! | ||
<pre> | <pre> | ||
| − | Channel Order -> TAER1234 ( | + | Channel Order -> TAER1234 (Needs Verification) |
</pre> | </pre> | ||
SAVE the page! | SAVE the page! | ||
| Line 28: | Line 28: | ||
---- | ---- | ||
| − | === | + | === FR Sky Transmitter settings: === |
MX16 Mode 2 transmitter and GR-16 receiver used for validations | MX16 Mode 2 transmitter and GR-16 receiver used for validations | ||
(Most common models expected to work the SAME)<br /> | (Most common models expected to work the SAME)<br /> | ||
Revision as of 13:32, 11 August 2019
Contents
Setup for using a FR Sky Tx/Rx
Always start with a reset/new transmitter model!
NOTE: You will use the 3-Pin to 4-Pin Male to Male cable provided to connect the FR Sky Rx to the FLEXF3. This is the same cable arrangement shown on page 15 of the manual for the Futaba connections. (Non-Telemetry)
CYPHER/Betaflight Settings
Use one of the Betaflight configuration tools to make these settings. Be sure to SAVE the configuration page after adjustments.
We have not tested Graupner Telemetry at this time. If you have information, you can send it to support@flexinnovations.com and we can update our content.
Configuration Page
Out of the box, only the 'Serial Receiver Provider' should need a change.
Receiver Mode -> Serial Based Receiver (Cypher Default) Serial Receiver Provider -> SBUS Telemetry slider -> OFF (Cypher Default)
SAVE the page!
Receiver Page
Should be same as out of box, but you can check!
Channel Order -> TAER1234 (Needs Verification)
SAVE the page!
FR Sky Transmitter settings:
MX16 Mode 2 transmitter and GR-16 receiver used for validations
(Most common models expected to work the SAME)
Receiver with diversity and SUMD out capability recommended.
You can verify the completed settings using the tools using the BetaFlight Receiver page.
Setup
Name: Cypher Model Type: Plane/Acro Wing type: 1 Ail, 0 Flaps (default) Tail type: Normal 1 Elev 1 Rudd (default) Throttles: 1 (default) The rest are defaults (default) Assign a 2-position switch to CH5 (Stability/Angle Mode) Assign a 3-position switch to CH6 (Configuration/Tilt) Bind your Transmitter and Receiver Set your system to output SUMD serial data No Subtrim should be used
Reversing
1 Throttle => 2 Aileron <= 3 Elevator => 4 Rudder <= 5 Gear => -or as desired 6 Aux1 <= -or as desired
NOTE: You can check 'reversing' by rotating the virtual 'body' on the Receiver Page of the Configurator
Travel
1 Throttle +-125% 2 Aileron +-125% 3 Elevator +-125% 4 Rudder +-125% 5 Profile-Stab +-125% 6 Config-Tilt +100 -60% To Start-Must adjust with gauges!
Go to the Receiver Page in Configurator and fine tune Aileron,Elevator, and Rudder travel to 1000-1500-2000. (See notes on top of Configurator page)
Timers
Set a count down
Timer length suggestion for first flights
2200mAh: 2:30
2600mAh: 3:10
3300mAh: 4:00
