Setup for using a FRSky Tx/Rx
Always start with a reset/new transmitter model!
- NOTE: You will use the 3-Pin to 4-Pin Male to Male cable provided to connect the FR Sky Rx to the FLEXF3. This is the same cable arrangement shown on page 15 of the manual for the Futaba connections. (Non-Telemetry)
- Use one of the Betaflight configuration tools to make these settings. Be sure to SAVE the configuration page after adjustments.
- We have not tested FRSky Telemetry at this time. If you have information, you can send it to firstname.lastname@example.org and we can update our content.
- Out of the box, only the 'Serial Receiver Provider' and 'Channel Map' below should need a change.
Receiver Mode -> Serial Based Receiver (Cypher Default) Serial Receiver Provider -> SBUS Telemetry slider -> OFF (Cypher Default)
- SAVE the page!
Channel Order -> AETR1234 (When Tx order is set to AETR)
- NOTE: AETR1234 is the order Futaba (creator of S.Bus) uses.
- SAVE the page!
FRSky Transmitter settings:
This page is under construction and is not considered 'confirmed' at this time. Do all command/control checks in the manual. Expert users please provide feedback to email@example.com
- This 3rd party Josh Bardwell Video should be very helpful when setting up and FRSky Taranis for Betaflight. It gives the general setup for Betaflight. You will need to note/set your CH5 and CH6 switch settings below.
-Note they set channel order to AETR (Set this) (2:50) -They pick a Quad Type, We suggest Airplane. (3:15) -8 Channels will be fine (or your preference) (5:55) -Good 'End Point' section (7:40) -Switch set example, but not Cypher specific, see below (11:35)
- This 3rd party GetFPV Video may also provide you with some general non-specific FRSky use background info.
- NOTE: Use a Receiver with diversity and SBUS out capability recommended.
- NOTE: You should verify the completed settings using the tools using the BetaFlight Receiver page.
Name: Cypher Model Type: Plane/Acro Wing type: 1 Ail, 0 Flaps (default) Tail type: Normal 1 Elev 1 Rudd (default) Throttles: 1 (default) The rest are defaults (default) Assign a 2-position switch to CH5 (Stability/Angle Mode) Assign a 3-position switch to CH6 (Configuration/Tilt) Bind your Transmitter and Receiver Set your system to output SBUS serial data Set the channel output order to AETR (Like Futaba for S.Bus) Significant Subtrim should not be required. (can set center to 1500 on receiver page)
1 Throttle -> † (These settings need confirmation, see NOTE†) 2 Aileron -> † 3 Elevator -> † 4 Rudder -> † 5 Gear ? -as desired for stability selection 6 Aux1 ?‡ -as desired for fan tilt 'switch' direction
- NOTE†: You must check Aileron, Elevator, Throttle 'Reversing' by rotating the virtual 'body' on the Receiver Page of the Configurator
- NOTE‡: The internal Flex pilots set the CH6 switch UP/Back for forward flight and Low/Front for Hover. You can set per your preference.
1 Throttle +-97% These all need validation on Rx page 2 Aileron +-97% 3 Elevator +-97% 4 Rudder +-97% 5 Profile-Stab +-97% 6 Config-Tilt +85 -55% To Start - Must adjust with gauges!
- Go to the Receiver Page in Configurator and fine tune Aileron,Elevator, and Rudder travel to 1000-1500-2000. (See notes on top of Configurator page)
Set a count down Timer length suggestion for first flights 2200mAh: 2:30 2600mAh: 3:10 3300mAh: 4:00