Cypher/JRDMSSInput

From Flex Innovations Wiki
Revision as of 15:13, 11 August 2019 by FlexTeam (Talk | contribs) (Setup for using a JR DMSS Tx/Rx)

Jump to: navigation, search

Setup for using a JR DMSS Tx/Rx


XBUS Connects like SBUS
Always start with a reset/new transmitter model!
NOTE: If your JR transmitter is DMSS, continue here. If it is DSM2 or DSMX, follow the Spektrum instructions!
NOTE: You will use the 3-Pin to 4-Pin Male to Male cable provided to connect the JR DMSS Rx to the FLEXF3. This is the same cable arrangement shown on page 15 of the manual for the Futaba connections. (Non-Telemetry)




CYPHER/Betaflight Settings

Use one of the Betaflight configuration tools to make these settings. Be sure to SAVE the configuration page after adjustments.

Configuration Page

Betaflight Serial Provider Setting
Betaflight Channel Map Setting
Betaflight JR Map Verify
Receiver Mode            ->  Serial Based Receiver (Cypher Default)
Serial Receiver Provider ->  XBUS_MODE_B           (aka JR XBUS MODE B)
Telemetry slider         ->  OFF                   (Cypher Default)
SAVE the page!

CLI Page

Channel Order            ->  AER2T134  Must be set in CLI Mode for JR DMSS!

To set, in your configurator, go to the 'CLI' page.
Cut and paste or type the following line into the command line:

   map AER2T134

Hit ENTER on the keyboard than paste or type:

   save

Hit ENTER on the keyboard. (This is NOT the 'Save to File' button)
You can VERIFY (but not pick) the rather unique AER2T134 settings on the Receiver Page.




JR DMSS Transmitter settings:

XG14 Mode 2 transmitter and R731BX Receiver used for validations. Choose a receiver capable of JR XBUS MODE B.
(Most common models expected to work the SAME)
You can verify the completed settings using the tools using the BetaFlight Receiver page.



Setup

Name:                  Cypher
Model Type:            Plane/Acro
Wing type:             1 Ail, 0 Flaps          (default)
Tail type:             Normal 1 Elev 1 Rudd    (default)
Throttles:             1                       (default)
The rest are defaults                          (default)
Assign a 2-position switch to CH5/Gear         (Stability/Angle Mode)
Assign a 3-position switch to CH6/Aux1         (Configuration/Tilt)
Bind your Transmitter and Receiver
In Transmitter menu, set Rx Output to JR Mode B
(FYI, this will disabled your Rx servo ports)

Reversing

1   Throttle        R  (Reversed)
2   Aileron         N 
3   Elevator        R  (Reversed)
4   Rudder          N
5   Gear            N  -or as desired
6   Aux1            N  -or as desired


Travel

Betaflight Travel Tune Notes
1    Throttle           +-88%    ???? Verify from Tx
2    Aileron            +-88%
3    Elevator           +-88%
4    Rudder             +-88%
5    Profile-Stab       +-88%
6    Config-Tilt        +70 -70%  To Start-Must adjust with gauges!
Go to the Receiver Page in Configurator and fine tune Aileron,Elevator, and Rudder travel to 1000-1500-2000. (See notes on top of Configurator page)



Timers

Set a count down
Timer length suggestion for first flights
     2200mAh:            2:30
     2600mAh:            3:10
     3300mAh:            4:00


Cypher Wiki Main