Difference between revisions of "F-100D 90mm EDF/ProFlapSetup"
From Flex Innovations Wiki
(→Center of Gravity) |
(→Pro Tips for Flap Setup) |
||
Line 10: | Line 10: | ||
====Flap Notes==== | ====Flap Notes==== | ||
*There is no one 'right way' to setup flaps. This page will give an example of setting up two flaps with one transmitter input with AURA using the F-100 PNP as an example. The techniques can be used in general in many situations. | *There is no one 'right way' to setup flaps. This page will give an example of setting up two flaps with one transmitter input with AURA using the F-100 PNP as an example. The techniques can be used in general in many situations. | ||
− | *We will assume 3-position scale type flaps set on a 3 position switch. The 'half flap' position will be set at (or near) the 'center' postion (aka transmitter data set at or near 0%. | + | *Typical settings (matches F-100D setup per manual) |
+ | **We will assume 3-position scale type flaps set on a 3 position switch. The 'half flap' position will be set at (or near) the 'center' postion (aka transmitter data set at or near 0%. | ||
+ | **Using Aura, transmitter wing type is set to 1 aileron, 1 flap | ||
+ | **Aura is set to two flaps and will setup two servo output ports (example S7, S8) using the 1 Tx/Rx Channel (CH6 is typical) | ||
− | ==== | + | ====Flap Setup==== |
*In addition to the JR DMSS receivers listed in the manual, the '''RG812BX''' should be a good choice as well. Avoid the '''BPX''' receivers as they will not do servo pulses and serial data at the same time. | *In addition to the JR DMSS receivers listed in the manual, the '''RG812BX''' should be a good choice as well. Avoid the '''BPX''' receivers as they will not do servo pulses and serial data at the same time. | ||
*We recommend updating to the very latest Aura Firmware '''v1.14''' or higher and then set the 'new to Aura' '''JR XBUS MODE A''' serial data in the transmitter and the Aura. | *We recommend updating to the very latest Aura Firmware '''v1.14''' or higher and then set the 'new to Aura' '''JR XBUS MODE A''' serial data in the transmitter and the Aura. |
Revision as of 16:03, 30 August 2020
--Under Construction--
Pro Tips for Flap Setup
Notes
Flap Notes
- There is no one 'right way' to setup flaps. This page will give an example of setting up two flaps with one transmitter input with AURA using the F-100 PNP as an example. The techniques can be used in general in many situations.
- Typical settings (matches F-100D setup per manual)
- We will assume 3-position scale type flaps set on a 3 position switch. The 'half flap' position will be set at (or near) the 'center' postion (aka transmitter data set at or near 0%.
- Using Aura, transmitter wing type is set to 1 aileron, 1 flap
- Aura is set to two flaps and will setup two servo output ports (example S7, S8) using the 1 Tx/Rx Channel (CH6 is typical)
Flap Setup
- In addition to the JR DMSS receivers listed in the manual, the RG812BX should be a good choice as well. Avoid the BPX receivers as they will not do servo pulses and serial data at the same time.
- We recommend updating to the very latest Aura Firmware v1.14 or higher and then set the 'new to Aura' JR XBUS MODE A serial data in the transmitter and the Aura.
- Using MODE A, you can physically wire/connect it just like Futaba diagram in the manual (P. 7). Throttle and Gear in the Receivers ports. Xbus to Port B in Aura.