Difference between revisions of "FlexJet/LatestUpdates"
From Flex Innovations Wiki
m |
(→Build Tips) |
||
| (77 intermediate revisions by 2 users not shown) | |||
| Line 6: | Line 6: | ||
=== Latest Online Manual === | === Latest Online Manual === | ||
| − | The Latest Version of the [http://resources.flexinnovations.com/Flex_Images/PDF_Library/Flex%20Jet%20Manual%20EN%20V1.0.pdf FlexJet (Rev - 1.0)] is available online. | + | The Latest Version of the [http://resources.flexinnovations.com/Flex_Images/PDF_Library/Flex%20Jet%20Manual%20EN%20V1.0.pdf '''FlexJet Manual (Rev - 1.0)'''] is available online. |
* This version matches the printed manual. (See add-in note on Gear Travel below) | * This version matches the printed manual. (See add-in note on Gear Travel below) | ||
* See Build Tips below for minor updates. | * See Build Tips below for minor updates. | ||
== Build Tips == | == Build Tips == | ||
| − | '''Initial Build''' | + | '''Initial Build'''[[File:FJG2_Retracts.jpg|thumb|upright=0.4|right|Retract & Strut Assembly]] |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | * | + | *On recent production, the '''Fin''' has the '''Spar Tube''' factory glued into it. In that case, simply plug the fin onto the fuselage, plug in the rudder servo, seat the fin and attach with the provided screws. (No additional glue is needed).[[File:FJG2_Clean_Receptical.jpg|thumb|upright=0.4|right|Clean the Recepticals]] |
| − | * | + | *On initial G2 shipments, we've noticed a few models that have the retract strut adapter pins installed on the incorrect sides, resulting in an aggressive toe-in angle in the main wheels. To correct:[[File:FJG2 Spars Installed.jpg|thumb|upright=0.4|right|Install Spars in Fuselage First]] |
| − | + | **Remove the retract units from the fuselage. | |
| − | *The Stab Linkage is located on the Outer-most hole from center at the | + | **Use a 1.5mm and 2mm hex driver to remove 2 set screws from the sides of the aluminum strut and 2 set screws from the sides of the retract housing. These set screws secure the strut to the pin, and the pin to the retract unit. |
| − | *The free Stab end Arm and Clevis can be turned together to make length adjustments while checking. Screw in place after correct trim is confirmed. (as described in Manual P. 11, Step 5) | + | **Slide the strut off the pin, then remove the pin. Swap the pins from left to right and re-install, being sure to use blue thread lock on the set screws, and ensure they rest against the flat spots on the pins. |
| − | *It is likely that your | + | **Re-install the retracts into the fuselage. Do not use blue thread lock on the retract mounting screws. |
| − | *Your Side Fairings behind the stab are likely NOT installed (change to prevent shipping damage). They are likely packed with your missile rails. Please glue them onto the aft fuselage with CA or Epoxy. | + | *Please set your transmitter '''CH5/Gear Travel''' to '''+-125%''' to ensure the '''Gear Sequencer''' will follow the transmitter and function properly. |
| − | *When re-installing the Tailpipe, a good technique is to get the tailpipe aligned with the back edge of the fan as close as possible, then 'pop' the aft end of the tailpipe with the open palm of your hand and it will 'jump' forward into place. | + | [[File:Stab_Fairing_5029.jpg|thumb|upright=0.4|right|Side Fairing Installation]] [[File:Stab Link 5022.jpg|thumb|upright=0.4|right|Linkage Installation]] |
| + | {{#ev:youtube|https://www.youtube.com/watch?v=dIjrTTspdAA|360|right|Stab/Tailpipe Video|frame}} | ||
| + | *'''FlexJet G2 Wing Installation''' | ||
| + | **The G2 has stronger receptacle tubes in the fuselage to accept the wing spars. It is possible that there could be a little residual glue in the tube or on the plywood near the plywood rib. There also could be a slight misalignment of the plywood rib to the tube. This could make it difficult to insert the Wing Tubes into the Fuselage. | ||
| + | **Test fit the Wing Tubes into the Fuselage (before installing the wings) using a twisting motion as needed. If it is too difficult to insert, use a #11 hobby knife to clean the plywood rib and the opening of the receptacle tube (a round file could also be used). | ||
| + | **Once the wing tubes are installed in the fuselage, slide the Wing Panels onto the tubes and finish securing the Wing. | ||
| + | *The '''Stab Linkage''' is located on the Outer-most hole from center at the '''Stab Arm End''' (aft end). Check/Connect the Clevis/Pushrod to the '''Stab Arm'''. | ||
| + | *The '''Stab Linkage''' is located the 2nd hole from the center at the '''Servo End'''. Attach the Stab Linkage to the '''Servo Arm'''. | ||
| + | *The free Stab end Arm and Clevis can be ''turned together'' to make pushrod length adjustments while checking. Screw the Arm in place after correct trim is confirmed. (as described in Manual P. 11, Step 5) | ||
| + | *It is likely that your '''Ventral Fins''' are already installed, so you may '''not''' have to install these per the manual. | ||
| + | *Your '''Side Fairings''' behind the stab are likely NOT installed (change to prevent shipping damage). They are likely packed with your missile rails. Please glue them onto the aft fuselage with CA or Epoxy before installing the tail cone. | ||
| + | *Please check the glue joints of the '''Rib''' in the fuselage socket where the wing attaches. Add some medium CA as needed. There have been several reports of inadequate glue. | ||
| + | *When re-installing the '''Tailpipe''', a good technique is to get the tailpipe aligned with the back edge of the fan as close as possible, then 'pop' the aft end of the tailpipe with the open palm of your hand and it will 'jump' forward into place. | ||
| + | <br /><br /> | ||
| + | [https://www.youtube.com/watch?v=dIjrTTspdAA '''Click to view a Stab/Tailpipe Instructional Video on YouTube'''] | ||
| + | <br /><br /><br /> | ||
| + | ---- | ||
| + | '''Full Build Video'''<br /> | ||
| + | [https://www.youtube.com/watch?v=JTJxbuKcS1I '''Click to view the Full Build Instructional Video on YouTube'''] | ||
| + | |||
| + | '''Timeline for specific segments of this video!'''<br /> | ||
| + | (Go to YouTube Page and you will have links)<br /> | ||
| + | <br />{{#ev:youtube|https://www.youtube.com/watch?v=JTJxbuKcS1I|360|right|Full Build Video|frame}} | ||
| + | [https://www.youtube.com/watch?v=JTJxbuKcS1I Introduction - 0:00]<br /> | ||
| + | [https://youtu.be/JTJxbuKcS1I?t=52 Required Tools and Accessories - 0:52]<br /> | ||
| + | [https://youtu.be/JTJxbuKcS1I?t=132 Spektrum Transmitter Setup - 2:02]<br /> | ||
| + | [https://youtu.be/JTJxbuKcS1I?t=383 Spektrum Receiver Installation - 6:23]<br /> | ||
| + | [https://youtu.be/JTJxbuKcS1I?t=607 Futaba Transmitter Setup - 10:07]<br /> | ||
| + | [https://youtu.be/JTJxbuKcS1I?t=1040 Futaba Receiver Installation - 17:20]<br /> | ||
| + | [https://youtu.be/JTJxbuKcS1I?t=1251 Removal of Tail Pipe and Exhaust Nozzle - 20:51]<br /> | ||
| + | [https://youtu.be/JTJxbuKcS1I?t=1402 Horizontal Stabilizer Installation - 23:22]<br /> | ||
| + | [https://youtu.be/JTJxbuKcS1I?t=1920 Main Wing Installation - 32:00]<br /> | ||
| + | [https://youtu.be/JTJxbuKcS1I?t=2157 Vertical Fin Installation - 35:57]<br /> | ||
| + | [https://youtu.be/JTJxbuKcS1I?t=2633 Tail Pipe and Nozzle Installation - 44:50]<br /> | ||
| + | [https://youtu.be/JTJxbuKcS1I?t=3014 Missile Rail Installation - 50:14]<br /> | ||
| + | [https://youtu.be/JTJxbuKcS1I?t=3070 Pre-Flight Checks - 51:10]<br /> | ||
| + | [https://youtu.be/JTJxbuKcS1I?t=3180 Outro - 53:00]<br /> | ||
| + | ---- | ||
<br /> | <br /> | ||
'''General Tips''' | '''General Tips''' | ||
| − | *It is possible to scrape the ventral fins and tail cone on the ground on landing. You can put a couple of layers of clear tape on the bottom of these to reduce wear | + | *It is possible to scrape the '''ventral fins''' and '''tail cone''' on the ground on landing. You can put a couple of layers of '''clear tape''' on the bottom of these to reduce wear |
| − | *As described in the manual, Arm the retracts before each flight. | + | *As described in the manual (P. 9, Top), Arm the '''retracts''' before each flight. |
| − | *Please read the Quick Trim section of the manual carefully, noting it has the ability to fine tune the Stab Trim in pitch and roll Before or After flying. | + | *Please read the '''Quick Trim''' section of the manual carefully, noting it has the ability to fine tune the Stab Trim in pitch and roll Before and/or After flying. |
'''Aura Tips''' | '''Aura Tips''' | ||
| − | *For Aura new comers, note that ANY Aura servo port (ex. Nose Wheel Steering) can be | + | *For Aura new comers, note that ANY Aura servo port (ex. Nose Wheel Steering) can be subtrimmed using the ''Aura Config Tool'' (set View->Advanced). Config Tool->Servo Ports->Subtrim. Be sure to ''WRITE'' to Aura to utilize the new settings. Most other parameters can also be adjusted in the ''Aura Config Tool'' |
| − | *For Aura veterans, please note that the FlexJet | + | *For Aura veterans, please note that the FlexJet uses '''Ch5/Gear''' for '''Retracts''' (2 position switch preferred), and '''Ch6/Aux1''' for '''Aura Flight Modes''' (3 position switch preferred). This is different than most of the previous 5 channel SPNP planes. |
Please consult the FlexJet Manual for Build instructions. | Please consult the FlexJet Manual for Build instructions. | ||
== Addendum == | == Addendum == | ||
| − | + | See Retract Sequencer, Fairing Attachment, and other notes. -Above- | |
== Parts Notes == | == Parts Notes == | ||
* The Left Main Landing Gear Door uses the NORMAL direction servo. '''FPZDS12''' | * The Left Main Landing Gear Door uses the NORMAL direction servo. '''FPZDS12''' | ||
* The Right Main Landing Gear Door and Nose Door use the REVERSE direction servo. '''FPZDS12R''' | * The Right Main Landing Gear Door and Nose Door use the REVERSE direction servo. '''FPZDS12R''' | ||
| + | * The Nose Wheel Steering uses the REVERSE direction servo. '''FPZDS12R''' | ||
* See the [http://www.flexinnovations.com/category-s/155.htm Part List Here] | * See the [http://www.flexinnovations.com/category-s/155.htm Part List Here] | ||
Latest revision as of 14:52, 16 June 2021
Contents
Latest Updates
Printed Manual Typo
None - See below
Latest Online Manual
The Latest Version of the FlexJet Manual (Rev - 1.0) is available online.
- This version matches the printed manual. (See add-in note on Gear Travel below)
- See Build Tips below for minor updates.
Build Tips
Initial Build
- On recent production, the Fin has the Spar Tube factory glued into it. In that case, simply plug the fin onto the fuselage, plug in the rudder servo, seat the fin and attach with the provided screws. (No additional glue is needed).
- On initial G2 shipments, we've noticed a few models that have the retract strut adapter pins installed on the incorrect sides, resulting in an aggressive toe-in angle in the main wheels. To correct:
- Remove the retract units from the fuselage.
- Use a 1.5mm and 2mm hex driver to remove 2 set screws from the sides of the aluminum strut and 2 set screws from the sides of the retract housing. These set screws secure the strut to the pin, and the pin to the retract unit.
- Slide the strut off the pin, then remove the pin. Swap the pins from left to right and re-install, being sure to use blue thread lock on the set screws, and ensure they rest against the flat spots on the pins.
- Re-install the retracts into the fuselage. Do not use blue thread lock on the retract mounting screws.
- Please set your transmitter CH5/Gear Travel to +-125% to ensure the Gear Sequencer will follow the transmitter and function properly.
- FlexJet G2 Wing Installation
- The G2 has stronger receptacle tubes in the fuselage to accept the wing spars. It is possible that there could be a little residual glue in the tube or on the plywood near the plywood rib. There also could be a slight misalignment of the plywood rib to the tube. This could make it difficult to insert the Wing Tubes into the Fuselage.
- Test fit the Wing Tubes into the Fuselage (before installing the wings) using a twisting motion as needed. If it is too difficult to insert, use a #11 hobby knife to clean the plywood rib and the opening of the receptacle tube (a round file could also be used).
- Once the wing tubes are installed in the fuselage, slide the Wing Panels onto the tubes and finish securing the Wing.
- The Stab Linkage is located on the Outer-most hole from center at the Stab Arm End (aft end). Check/Connect the Clevis/Pushrod to the Stab Arm.
- The Stab Linkage is located the 2nd hole from the center at the Servo End. Attach the Stab Linkage to the Servo Arm.
- The free Stab end Arm and Clevis can be turned together to make pushrod length adjustments while checking. Screw the Arm in place after correct trim is confirmed. (as described in Manual P. 11, Step 5)
- It is likely that your Ventral Fins are already installed, so you may not have to install these per the manual.
- Your Side Fairings behind the stab are likely NOT installed (change to prevent shipping damage). They are likely packed with your missile rails. Please glue them onto the aft fuselage with CA or Epoxy before installing the tail cone.
- Please check the glue joints of the Rib in the fuselage socket where the wing attaches. Add some medium CA as needed. There have been several reports of inadequate glue.
- When re-installing the Tailpipe, a good technique is to get the tailpipe aligned with the back edge of the fan as close as possible, then 'pop' the aft end of the tailpipe with the open palm of your hand and it will 'jump' forward into place.
Click to view a Stab/Tailpipe Instructional Video on YouTube
Full Build Video
Click to view the Full Build Instructional Video on YouTube
Timeline for specific segments of this video!
(Go to YouTube Page and you will have links)
Introduction - 0:00
Required Tools and Accessories - 0:52
Spektrum Transmitter Setup - 2:02
Spektrum Receiver Installation - 6:23
Futaba Transmitter Setup - 10:07
Futaba Receiver Installation - 17:20
Removal of Tail Pipe and Exhaust Nozzle - 20:51
Horizontal Stabilizer Installation - 23:22
Main Wing Installation - 32:00
Vertical Fin Installation - 35:57
Tail Pipe and Nozzle Installation - 44:50
Missile Rail Installation - 50:14
Pre-Flight Checks - 51:10
Outro - 53:00
General Tips
- It is possible to scrape the ventral fins and tail cone on the ground on landing. You can put a couple of layers of clear tape on the bottom of these to reduce wear
- As described in the manual (P. 9, Top), Arm the retracts before each flight.
- Please read the Quick Trim section of the manual carefully, noting it has the ability to fine tune the Stab Trim in pitch and roll Before and/or After flying.
Aura Tips
- For Aura new comers, note that ANY Aura servo port (ex. Nose Wheel Steering) can be subtrimmed using the Aura Config Tool (set View->Advanced). Config Tool->Servo Ports->Subtrim. Be sure to WRITE to Aura to utilize the new settings. Most other parameters can also be adjusted in the Aura Config Tool
- For Aura veterans, please note that the FlexJet uses Ch5/Gear for Retracts (2 position switch preferred), and Ch6/Aux1 for Aura Flight Modes (3 position switch preferred). This is different than most of the previous 5 channel SPNP planes.
Please consult the FlexJet Manual for Build instructions.
Addendum
See Retract Sequencer, Fairing Attachment, and other notes. -Above-
Parts Notes
- The Left Main Landing Gear Door uses the NORMAL direction servo. FPZDS12
- The Right Main Landing Gear Door and Nose Door use the REVERSE direction servo. FPZDS12R
- The Nose Wheel Steering uses the REVERSE direction servo. FPZDS12R
- See the Part List Here
