Difference between revisions of "RV-8 60E G2/Crow"
From Flex Innovations Wiki
(Created page with "{{DISPLAYTITLE:How to Setup your RV-8 60E G2 Transmitter}} __FORCETOC__ <!-- This forces the Table of Contents since it has less than 3 levels --> == Crow Quick Set Procedure...") |
m |
||
Line 1: | Line 1: | ||
− | {{DISPLAYTITLE:How to | + | {{DISPLAYTITLE:How to Enable/Disable the Crow Switch using Quick Set from your Transmitter}} |
__FORCETOC__ <!-- This forces the Table of Contents since it has less than 3 levels --> | __FORCETOC__ <!-- This forces the Table of Contents since it has less than 3 levels --> | ||
== Crow Quick Set Procedure for RV-8 60E G2 == | == Crow Quick Set Procedure for RV-8 60E G2 == | ||
Line 18: | Line 18: | ||
=== Step 2 - Choose Crow Option === | === Step 2 - Choose Crow Option === | ||
After entering Quick Set mode as described above, toggle the CH8/Aux3 channel switch on the transmitter to ENABLE or DISABLE the Crow functionality. | After entering Quick Set mode as described above, toggle the CH8/Aux3 channel switch on the transmitter to ENABLE or DISABLE the Crow functionality. | ||
− | * If the Red LED is | + | * If the Red LED is ON, the Crow option is ENABLED in the Aura. |
* If the Red LED is OFF, the Crow option is DISABLED in the Aura. | * If the Red LED is OFF, the Crow option is DISABLED in the Aura. | ||
Line 26: | Line 26: | ||
# Completely power off the RV-8 and Aura | # Completely power off the RV-8 and Aura | ||
# Replace the Servo Lead in Aura Port S2 | # Replace the Servo Lead in Aura Port S2 | ||
− | # Power up, confirm that the Crow option can | + | # Power up, confirm that the Crow option can be activated with the CH8/Aux3 Switch and Fly! |
<noinclude> | <noinclude> |
Revision as of 22:52, 30 June 2023
Contents
Crow Quick Set Procedure for RV-8 60E G2
To enter Quick Set mode, the Aura must receive a valid signal from the Receiver when the Aura is powered up.
Make sure your Transmitter is setup with your CH8/Aux3 channel assigned to a 2 Position switch for Crow.
Step 1 - Enter Quick Set mode
- Make sure all power is off on the RV-8 60E G2
- Remove the prop before making changes
- Turn on your transmitter
- Remove the Servo lead from Aura Port S2.
- Put a bind plug in Aura Port S2.
- Plug in the battery to power up the RV-8 60E G2
- The Orange LED will be OFF while the Green LED is ON indicating you are in the Quick Set mode and receiving a valid signal from the Receiver.
Step 2 - Choose Crow Option
After entering Quick Set mode as described above, toggle the CH8/Aux3 channel switch on the transmitter to ENABLE or DISABLE the Crow functionality.
- If the Red LED is ON, the Crow option is ENABLED in the Aura.
- If the Red LED is OFF, the Crow option is DISABLED in the Aura.
Step 3 - Save the desired Crow Option
- After correctly toggling the CH8/Aux3 switch to Enable or Disable the Crow option, remove the bind plug save the settings.
- The LEDs will turn on while the Aura is saving, then will go back to their previous state.
- Completely power off the RV-8 and Aura
- Replace the Servo Lead in Aura Port S2
- Power up, confirm that the Crow option can be activated with the CH8/Aux3 Switch and Fly!