Aura/ConfigFiles - Revision history

FlexTeam at 00:24, 21 June 2019

2019-06-21T00:24:41Z

FlexTeam: /* Aura Config Files by the Flex Innovations Team */

2018-01-23T18:42:27Z

‎Aura Config Files by the Flex Innovations Team

WikiSys at 22:46, 28 March 2017

2017-03-28T22:46:47Z

FlexTeam at 17:09, 9 March 2017

2017-03-09T17:09:32Z

FlexTeam: /* Mamba Biplane with Crow (FM Activation) */

2016-09-13T17:15:07Z

‎Mamba Biplane with Crow (FM Activation)

FlexTeam: /* Mamba Biplane with Crow (FM Activation) */

2016-09-13T17:10:53Z

‎Mamba Biplane with Crow (FM Activation)

FlexTeam: /* Mamba Biplane with Crow (FM Activation) */

2016-09-13T17:10:22Z

‎Mamba Biplane with Crow (FM Activation)

FlexTeam at 16:26, 24 August 2016

2016-08-24T16:26:14Z

FlexTeam: /* Mamba Biplane with Crow (FM Activation) */

2016-06-01T17:31:11Z

‎Mamba Biplane with Crow (FM Activation)

FlexTeam at 17:28, 1 June 2016

2016-06-01T17:28:06Z

← Older revision		Revision as of 00:24, 21 June 2019
Line 141:		Line 141:
	**[http://www.resources.flexinnovations.com/aura/auraConfigFiles/PKZ_Habu_Foamie_FLEX_B.acf ParkZone Habu Aura File]		**[http://www.resources.flexinnovations.com/aura/auraConfigFiles/PKZ_Habu_Foamie_FLEX_B.acf ParkZone Habu Aura File]

		+	[[Aura\|Aura Wiki Main]]
	<noinclude>[[Category:Aura\|Aura]]</noinclude>		<noinclude>[[Category:Aura\|Aura]]</noinclude>

@@ Line 3: / Line 3: @@
 Aura Config Files can be downloaded and saved to your PC. Use the Aura Config Tool to open the file.  Each file can be reviewed, modified, and saved as needed.
-For additional information, check [[Aura/Install|Installing your Aura]] and [[Aura/Configure|Configuring your Aura]].  We currently support Spektrum (DSM2/X), Futaba, Graupner, Jeti, and JR DMSS Transmitters.  For FR Sky, we recommend using our [http://www.resources.flexinnovations.com/aura/txModels/auraFrSky_1-0.bin Custom FR Sky Transmitter File] for easiest setup. All Transmitters are supported via PWM/Custom setup.
+For additional information, check [[Aura/Install|Installing your Aura]] and [[Aura/Configure|Configuring your Aura]].  We currently support Spektrum (DSM2/X), Futaba, Graupner, Jeti, and JR DMSS Transmitters. We also have tested the Hitec "SL" (s.bus) connection to Aura and have a page on that.  For FR Sky, we recommend using our [http://www.resources.flexinnovations.com/aura/txModels/auraFrSky_1-0.bin Custom FR Sky Transmitter File] for easiest setup. All Transmitters are supported via PWM/Custom setup.
 Do NOT fly any model without carefully checking the sensor and transmitter response. Servo Ports are labeled/named on the Servo Port Tab of the Aura Config Tool Application.

← Older revision		Revision as of 22:46, 28 March 2017
Line 140:		Line 140:
	*Downloads:		*Downloads:
	**[http://www.resources.flexinnovations.com/aura/auraConfigFiles/PKZ_Habu_Foamie_FLEX_B.acf ParkZone Habu Aura File]		**[http://www.resources.flexinnovations.com/aura/auraConfigFiles/PKZ_Habu_Foamie_FLEX_B.acf ParkZone Habu Aura File]
		+
		+	<noinclude>[[Category:Aura\|Aura]]</noinclude>

@@ Line 42: / Line 42: @@
 **[http://www.resources.flexinnovations.com/aura/auraConfigFiles/VentiqueConfigFrSkyAuto.acf FrSky X9D+ Transmitter with Receiver Auto-Detect]
-===Mamba Biplane with Crow (FM Activation)===
+===Mamba 70cc Biplane with Crow (FM Activation)===
 This is a relatively advanced example of a 4 servo biplane with Crow Enabled. It does NOT require an extra channel for Crow, Crow is driven only by selection of FM1, with Aura Mixes from throttle into a 'proxy Channel (21)' to split the ailerons using Custom settings in the Servo Ports Tab. Gyro's are able to be in the loop at all times, and at optimum stick priority gain mapping.
@@ Line 77: / Line 77: @@
 Pay attention to the Crow Aura Mix 1 vs Tx Reversing of the throttle Channel. If the throttle servo direction or geometry is opposite ours, the Aura Throttle to Ch21 Mix will likely need to be 'flipped' to the 'other side'.
-===Mamba Biplane without Crow===
+===Mamba 70cc Biplane without Crow===
 This is a Mamba file without Crow.

@@ Line 71: / Line 71: @@
 Relevant CH6 settings in the T8J are: Switch E set to change CH6 Data, CH6 Direction=Reversed, CH6/FLP Travel=0/100. (The Zero will give Centered CH6 output which is Gyro Gain (ON) values as Set in the Aura Config Tool, and the '100' will give CH6 Low output which is Gyro Gain OFF, you can check this in your Transmitter Monitor and with Live Data in the Aura Config Tool.)
-You can easily change the 'Master Gain' to another channel as desired by changing the Master Gain source on each and every Control Mode that is used in the Control Mode Tab.
+'''When using a switch for master gain, be sure that the ON setting has the channel data CENTERED, and the OFF setting has the data 100% in direction as needed to turn the gyro inputs OFF. (Having the ON setting at 100% instead of CENTERED will ''double'' the gain and cause dangerous oscillations!)'''
 Pay attention to the Crow Aura Mix 1 vs Tx Reversing of the throttle Channel. If the throttle servo direction or geometry is opposite ours, the Aura Throttle to Ch21 Mix will likely need to be 'flipped' to the 'other side'.

@@ Line 46: / Line 46: @@
 This is a relatively advanced example of a 4 servo biplane with Crow Enabled. It does NOT require an extra channel for Crow, Crow is driven only by selection of FM1, with Aura Mixes from throttle into a 'proxy Channel (21)' to split the ailerons using Custom settings in the Servo Ports Tab. Gyro's are able to be in the loop at all times, and at optimum stick priority gain mapping.
 *If not using Futaba S.bus, it Requires an other Digital or 8 PPM N Input to be selected by the USER
-*3 flight modes (FM1:Med Rate/High Gain/Crow, FM2:Low Rate/Low Gain/No crow, FM3:High Rate/High Gain/No Crow)
+*3 flight modes (FM1:Med Rate/High Gain/Crow, FM2:Low Rate/Low Gain/No crow, FM3:High Rate/High Gain/No Crow) switched by CH5/Gear
 *Quick Set: Disabled
 *Quick Trim: Enabled

@@ Line 67: / Line 67: @@
 ::Tips: Focus on the normal aileron setup first getting them centered (Aura Sub-Trim), and with equal (or as desired with Aura Output Scale) travel on each surface using a ruler and the Output Scale adjustments for each Servo/Port. After setting the Transmitter Throttle settings as required, next add/deploy the crow, and use the Ailerons Servo Port Source 2 Mix values (and/or Aura Mix 1 value) and the ruler to put equal (or as desired) Crow into each Aileron.
-:* This program was flown with a Futaba T8J Transmitter. Since all 3 Flight Modes are 'Gyro Enabled', for safety/test a 2-position switch is used to on the Master Gain to turn the Gyro action on/off with CH6. Perform the take-off and climb to safe altitude with the gyro off.
+:* This program was flown with a Futaba T8J Transmitter. Since all 3 Flight Modes (switched by CH5/Gear) are 'Gyro Enabled', for safety/test a 2-position switch is used to on the Master Gain to turn the Gyro action on/off with CH6. Perform the take-off and climb to safe altitude with the gyro off.
 Relevant CH6 settings in the T8J are: Switch E set to change CH6 Data, CH6 Direction=Reversed, CH6/FLP Travel=0/100. (The Zero will give Centered CH6 output which is Gyro Gain (ON) values as Set in the Aura Config Tool, and the '100' will give CH6 Low output which is Gyro Gain OFF, you can check this in your Transmitter Monitor and with Live Data in the Aura Config Tool.)

← Older revision		Revision as of 17:31, 1 June 2016
Line 70:		Line 70:

	Relevant CH6 settings in the T8J are: Switch E set to change CH6 Data, CH6 Direction=Reversed, CH6/FLP Travel=0/100. (The Zero will give Centered CH6 output which is Gyro Gain (ON) values as Set in the Aura Config Tool, and the '100' will give CH6 Low output which is Gyro Gain OFF, you can check this in your Transmitter Monitor and with Live Data in the Aura Config Tool.)		Relevant CH6 settings in the T8J are: Switch E set to change CH6 Data, CH6 Direction=Reversed, CH6/FLP Travel=0/100. (The Zero will give Centered CH6 output which is Gyro Gain (ON) values as Set in the Aura Config Tool, and the '100' will give CH6 Low output which is Gyro Gain OFF, you can check this in your Transmitter Monitor and with Live Data in the Aura Config Tool.)
		+
		+	You can easily change the 'Master Gain' to another channel as desired by changing the Master Gain source on each and every Control Mode that is used in the Control Mode Tab.

	Pay attention to the Crow Aura Mix 1 vs Tx Reversing of the throttle Channel. If the throttle servo direction or geometry is opposite ours, the Aura Throttle to Ch21 Mix will likely need to be 'flipped' to the 'other side'.		Pay attention to the Crow Aura Mix 1 vs Tx Reversing of the throttle Channel. If the throttle servo direction or geometry is opposite ours, the Aura Throttle to Ch21 Mix will likely need to be 'flipped' to the 'other side'.

← Older revision		Revision as of 17:28, 1 June 2016
Line 60:		Line 60:

	Note: Follow the normal [[Aura/Install#2._Transmitter_Setup\|Aura Transmitter set-up instructions]] (A freshly reset transmitter model while making the few changes per the instructions. Maintain normal wing and tail type with single Aileron, Elevator, and Rudder channels)		Note: Follow the normal [[Aura/Install#2._Transmitter_Setup\|Aura Transmitter set-up instructions]] (A freshly reset transmitter model while making the few changes per the instructions. Maintain normal wing and tail type with single Aileron, Elevator, and Rudder channels)
		+
		+	Note: You can see the control surface Port assignments in the Servo Ports Tab.

	You can easily 'build' on this model and customize it. If you want 'crow' driven by transmitter data, instead of a 'proxy', simply disable Aura Mix 1 and use a transmitter channel (ex: CH7) instead of Ch 21 as Source 2 on the Servo Ports Tab (all Ailerons).		You can easily 'build' on this model and customize it. If you want 'crow' driven by transmitter data, instead of a 'proxy', simply disable Aura Mix 1 and use a transmitter channel (ex: CH7) instead of Ch 21 as Source 2 on the Servo Ports Tab (all Ailerons).