Aura/GraupnerHottUse - Revision history

FlexTeam: /* Graupner Hott Use */

2020-08-12T21:43:09Z

‎Graupner Hott Use

FlexTeam: /* Graupner SUMD Update September 2019 */

2019-10-01T18:54:22Z

‎Graupner SUMD Update September 2019

FlexTeam: /* Graupner SUMD Update September 2019 */

2019-10-01T18:53:02Z

‎Graupner SUMD Update September 2019

FlexTeam: /* Graupner SUMD Update September 2019 */

2019-10-01T18:52:40Z

‎Graupner SUMD Update September 2019

FlexTeam: /* Graupner SUMD Update September 2019 */

2019-09-24T13:55:24Z

‎Graupner SUMD Update September 2019

FlexTeam: /* General */

2019-09-24T13:53:05Z

‎General

FlexTeam: /* General */

2019-09-24T13:52:26Z

‎General

FlexTeam: /* Graupner SUMD Update September 2019 */

2019-09-24T13:49:47Z

‎Graupner SUMD Update September 2019

FlexTeam: /* Graupner SUMD Update September 2019 */

2019-09-24T13:48:46Z

‎Graupner SUMD Update September 2019

FlexTeam: /* Graupner SUMD Update September 2019 */

2019-09-24T13:47:45Z

‎Graupner SUMD Update September 2019

← Older revision		Revision as of 21:43, 12 August 2020
Line 3:		Line 3:
	=Graupner Hott Use=		=Graupner Hott Use=

−	~~-Under Construction-~~
	We welcome user contact and information.		We welcome user contact and information.

@@ Line 23: / Line 23: @@
 **Connect to '''Aura B Port''' (set SUMDof12 manually in Aura Config Tool)
-*Tested '''GR-12L S1051''' dual antenna diversity micro receiver.[[File:GR-12L SUMD S1051.jpg|thumb|upright=0.42|right|Note SUMD Output]]
+*Tested '''GR-12L S1051''' dual antenna diversity micro receiver.[[File:GR-12L SUMD S1051.jpg|thumb|upright=0.42|right|GR-12L - S1051 Note SUMD Output]]
 **The instructions are very limited! [https://www.graupner.de/media/pdf/ab/f6/f2/S1045_S1046_S1051_SUMD_Diversity_Receiver_DE_V1sh_.pdf '''GR-12L S1051 Manual''']
 **Firmware 2.04

@@ Line 33: / Line 33: @@
 *Tested '''GR-16L'''
 **Firmware 7.07
-**Set '''SUMDof8''' on the '''Port '''8''' of the Rx''' (Usually set in Graupner Tx Telemetry menu.)
+**Set '''SUMDof8''' on the '''Port 8 of the Rx''' (Usually set in Graupner Tx Telemetry menu.)
 **Set '''SUMDof8''' for '''Port B of Aura'''. Connect these ports with Male to Male cable
 ::(Aura can also Auto-Detect SUMDof8 if Auto-Detect is enabled)

@@ Line 33: / Line 33: @@
 *Tested '''GR-16L'''
 **Firmware 7.07
-**Set '''SUMDof8''' on the '''Port 8 of the Rx''' (Usually set in Graupner Tx Telemetry menu.)
+**Set '''SUMDof8''' on the '''Port '''8''' of the Rx''' (Usually set in Graupner Tx Telemetry menu.)
 **Set '''SUMDof8''' for '''Port B of Aura'''. Connect these ports with Male to Male cable
 ::(Aura can also Auto-Detect SUMDof8 if Auto-Detect is enabled)
@@ Line 40: / Line 40: @@
 **Firmware 2.04
 **Graupner Gyros NOT enabled.
-**Puts out '''SUMDof16''' on Rx Port 8  (set manually in Aura Config Tool)
+**Puts out '''SUMDof16''' on Rx Port '''6'''  (set manually in Aura Config Tool)
 <br />
 ----

@@ Line 49: / Line 49: @@
 *With your receiver bound, test that the receiver can drive a servo normally (Bind Check)
 *Go into your transmitter menu structure following its instructions (sometimes in Telemetry menu) and Enable SUMD (This must be done, it is '''not done/on''' automatically/by default). Note which pin/servo port the SumD is assigned to on your Rx Bus.
-*Taking extra care with the polarity, connect the SumD Rx port to servo Port B of the Aura using one male-to-male cable.
+*Taking extra care with the polarity, connect the SumD Rx port to servo Port B of the Aura (Port A for Aura Professional) using one male-to-male cable.
-*Most of our testing has been with SUMD of 8, and of 12.
+*Most of our testing has been with SUMD of 8, of 12, and of 16.
-**It seems the GR16 defaults to SumD of 8 (using our MX-16)
+**It seems the GR-16 defaults to SumD of 8 (using our MX-16)
-**It seems the GR12L may default to SumD of 12 (using our MX-16) (Not Confirmed)
+**It seems the GR-12L Single Antenna defaults to SumD of 12 (using our MX-16) (Not Confirmed)
-*The GR16 is easiest to use on PNP aircraft like the QQ Extra and Cessna 170, or with Quick Set on the Open Stock Aura. Aura can Auto-Detect SumD of 8 (unless Auto-Detect is disabled, refer to your products user guide.)
+*The GR-16 is easiest to use on PNP aircraft like the QQ Extra and Cessna 170, or with Quick Set on the Open Stock Aura. Aura can Auto-Detect SumDof8 (unless Auto-Detect is disabled, refer to your products user guide.)
 *Some Graupner transmitters or devices may allow you to re-program the SumD channel count?
 *As needed, use the Aura Config tool to go in and select  the correct radio settings for Aura

@@ Line 14: / Line 14: @@
 The specific equipment we have tested and flown includes an ''MX-16'' transmitter, and ''GR-16'' and other Receivers.
-It seems difficult or impossible to find published data on what SUMD format all the different receivers support (or default to). At times you may need to got though the entire list on the Aura Config Tool and look for the solid green LED when connected. 8, 12, and 16 being by far the most common SUMD outputs.
+It seems difficult or impossible to find published data on what SUMD format all the different receivers support (or default to). At times you may need to got though the entire list on the Aura Config Tool and look for the solid green LED when connected, with 8, 12, and 16 being by far the most common SUMD outputs.
 ==='''Graupner SUMD Update September 2019'''===

@@ Line 11: / Line 11: @@
 We are NOT experts on the Graupner Hott system.
 We did implement and thoroughly test their single wire 'digital' SRXL Protocol '''SUMD'''.
-Aura can get 12+ channels of data on a single wire using '''SUMD'''.
+Aura can get 8, 12, or even 16 channels of data on a single wire using '''SUMD'''.
-The specific equipment we have tested and flown includes an ''MX-16'' transmitter, and ''GR16'' Receivers.
+The specific equipment we have tested and flown includes an ''MX-16'' transmitter, and ''GR-16'' and other Receivers.
-It seems difficult or impossible to find published data on what SumD format the different receivers support (or default to).
+It seems difficult or impossible to find published data on what SUMD format all the different receivers support (or default to). At times you may need to got though the entire list on the Aura Config Tool and look for the solid green LED when connected. 8, 12, and 16 being by far the most common SUMD outputs.
 ==='''Graupner SUMD Update September 2019'''===

@@ Line 20: / Line 20: @@
 **Firmware 2.05
 **Single antenna likely good only for small close-in parkflyers.
-**Puts out '''SUMDof12''' on Rx Port 6 (set manually in Aura Config Tool)
+**Puts out '''SUMDof12''' on '''Rx Port 6'''
 *Tested '''GR-12L S1051''' dual antenna diversity micro receiver.[[File:GR-12L SUMD S1051.jpg|thumb|upright=0.42|right|Note SUMD Output]]

@@ Line 26: / Line 26: @@
 **Firmware 2.04
 **Puts out '''SUMDof16''' on the Ch6/SUMD male cable (Set manually in Aura Config Tool)
-**Male SUMD cable can connect directly to Aura 8 B Port
+**Male SUMD cable can connect directly to '''Aura 8 B Port'''
 **Made no connection between the telemetry cable and Aura.
 **Good for planes that DO NOT require additional receiver servo ports such as throttle.