Aura/HitecSbusUse - Revision history

FlexTeam at 00:27, 21 June 2019

2019-06-21T00:27:18Z

2019-06-11T18:33:30Z

2019-06-11T18:33:09Z

‎Hitec Installation Notes and Equipment Selection

2019-06-11T18:32:56Z

2019-06-11T18:32:05Z

2019-06-11T18:31:21Z

2019-06-11T18:30:09Z

‎Notes on using Hitec S.Bus

2019-06-11T18:29:50Z

2019-06-11T18:29:03Z

‎Hitec S.Bus Transmitter Programming/Changes

2018-04-07T13:48:57Z

← Older revision		Revision as of 00:27, 21 June 2019
Line 80:		Line 80:
	=== Additional information for [[Aura/LargeAircraftInstall\|Large Aircraft Installs]]. ===		=== Additional information for [[Aura/LargeAircraftInstall\|Large Aircraft Installs]]. ===

		+	[[Aura\|Aura Wiki Main]]
	<noinclude>[[Category:Aura\|Aura]]</noinclude>		<noinclude>[[Category:Aura\|Aura]]</noinclude>

@@ Line 26: / Line 26: @@
 *These notes supplement (add to/modify) the normal Transmitter setup (Aura Instructions) that you should follow.
 *Connect the Recievers SL Port to the Aura Servo Port B with a male to male servo type connector
-'''NOTE''': For '''Aura Professionals''', it is preferred to put the SBUS into Port A.
+:'''NOTE''': For '''Aura Professionals''', it is preferred to put the SBUS into Port A.
 *Hitec has elected to use the Futaba Header Bytes ID Code, so the Aura will work and/or auto-detect as a "Futaba S.Bus"
 *Hitec has duplicated some of the Futaba data format standards such as Channel Order in the data

@@ Line 7: / Line 7: @@
 * S.Bus (SL or Single Line is the Hitec implementation of Futaba S.Bus)
 * Traditional PWM Servo Connection
-'''NOTE:''' Any recommendations are based on years of knowledge and product use and are informational only.
+:'''NOTE:''' Any recommendations are based on years of knowledge and product use and are informational only.
 * We do not 'specify' radio installations. Consult your radio manufacturer for radio information.
 * We test and support the use of genuine Hitec brand equipment.

@@ Line 1: / Line 1: @@
 {{DISPLAYTITLE:Hitec Use - General Notes}}
 == Hitec Installation Notes and Equipment Selection ==
-'''Note: This page is a Draft/Work in Progress. We request feedback from customers to make this page better based on your experience.'''
+'''Note: We request feedback from customers to make this page better based on your experience.'''
-−
 [mailto:aurasupport@flexinnovations.com? E-mail Aura Support]

@@ Line 54: / Line 54: @@
 *You can save a copy of this 'basic' Tx program in you transmitter to copy as a starting point for future Aura equipped models. All will start from the same foundation.
 *Aura will be set/used/auto-detected as a '''FUTABA -> SBUS -> SERVO PORT B'''. Aura will otherwise work completely normally, you can even fly the PNP models (via Auto-Detect) with no need to change any Aura settings.
-'''NOTE''': For '''Aura Professionals''', it is preferred to put the SBUS into Port A.
+:'''NOTE''': For '''Aura Professionals''', it is preferred to put the SBUS into Port A.
 <br />
 '''You can check the data input to Aura using the Aura Config Tool''' (Windows App) with the system all connected and active using 'Live Data' feature in the Aura Config Tool

@@ Line 30: / Line 30: @@
 *Hitec has elected to use the Futaba Header Bytes ID Code, so the Aura will work and/or auto-detect as a "Futaba S.Bus"
 *Hitec has duplicated some of the Futaba data format standards such as Channel Order in the data
-*Hitec has chosen '''NOT to duplicate''' other Futaba data standards such as channel center data values, and default direction of travel away from center.
+*Hitec has chosen '''NOT to duplicate''' other Futaba data standards such as channel '''center data''' values, and default '''direction''' of travel away from center.
 === Hitec S.Bus Transmitter Programming/Changes  ===

@@ Line 73: / Line 73: @@
 **See Aura or SPNP Aircraft instructions for Port Connections.
 **Working Rx Ports other than Aileron, Elevator, Rudder, and Flight Mode (default is CH5) will be available (Receiver bus).
-*See notes above, use Aura input monitor and methods above to acheive correct input direction and 0 +-125% for Aileron, Elevator, and Rudder
+*See notes above, use Aura 'Input Monitor' and methods above/as required to achieve correct input direction and 0%, +-125% for Aileron, Elevator, and Rudder
 == Installing your Aura ==