Cypher/Telemetry - Revision history

FlexTeam: /* Jeti Telemetry */

2019-09-20T21:12:46Z

‎Jeti Telemetry

2019-09-20T21:10:09Z

‎Futaba Telemetry

2019-09-06T14:53:38Z

‎Jeti Telemetry

2019-09-06T14:49:34Z

‎Spektrum Telemetry

2019-09-06T14:48:45Z

‎General Telemetry Information (Telemetry is Optional)

2019-08-10T19:26:41Z

‎Spektrum Telemetry

2019-08-10T19:26:07Z

‎Spektrum Telemetry

2019-08-10T19:23:27Z

‎Jeti Telemetry

2019-08-08T00:43:33Z

‎Jeti Telemetry

2019-08-08T00:42:59Z

‎JR DMSS

@@ Line 69: / Line 69: @@
 *Fabricate the Custom 3-pin to 4-pin male -to- male cable. (You can use the supplied two cables for parts)[[File:BF_Jeti_Cable3_1400.jpg|thumb|upright=0.42|right|Jeti Telemetry Cable Photo]]
 **Remove insulation from the middle of the 'signal' wire.
-**'Y' the wire and install a 2.2k Ohm 1/4 watt resistor as shown in image at right. (You can find on Amazon for example)
+**'Y' the wire and solder in a 2.2k Ohm 1/4 watt resistor as shown in image at right. (You can find on Amazon for example)
 **Insulate with heat shrink tubing.
 *Connect the receiver to the FLEXF3 using the first 3 pins (-,+,signal) at the Receivers's EX Bus Port and 4-pins at the FLEXF3 (-,+,Rx,Tx)

@@ Line 45: / Line 45: @@
 ==Futaba Telemetry==
 *These instructions supplement the non-telemetry setup instructions in the Cypher manual.
-*Only Telemetry provided by the '''Rx''' is available. Receivers are available that can sample Main Flight Pack Voltage.
+*Only Telemetry provided by the '''FUTABA Rx''' is available. Receivers are available that can sample Main Flight Pack Voltage.
 *'''Betaflight/FLEXF3 Data not available''', so no Betaflight settings are made.
 *To connect the '''Receiver's''' telemetry to the Cypher's flight pack voltage tap:

@@ Line 71: / Line 71: @@
 **'Y' the wire and install a 2.2k Ohm 1/4 watt resistor as shown in image at right. (You can find on Amazon for example)
 **Insulate with heat shrink tubing.
-*Connect to '''FLEXF3''' using the first 3 pins (-,+,signal) at the Rx's EX Bus Port and 4-pins at the FLEXF3 (-,+,Rx,Tx)
+*Connect the receiver to the FLEXF3 using the first 3 pins (-,+,signal) at the Receivers's EX Bus Port and 4-pins at the FLEXF3 (-,+,Rx,Tx)
 *Use your configuration tool to: (hit the pages 'Save' button before leaving each page)[[File:BF_Telemetry_F.jpg|thumb|upright=0.42|right|Set Telemetry Slider and Save]]
 **On '''Configuration''' page

@@ Line 21: / Line 21: @@
 ==Spektrum Telemetry==
 *These instructions supplement the non-telemetry setup instructions in the Cypher manual.
-*Easy to setup (really just the third pin plug and telemetry slider in configurator) and provides the following '''Telemetry Data''':
+*Easy to setup ('''really just the third pin plug and telemetry slider in configurator''') and provides the following '''Telemetry Data''':
 **Provided by '''Rx''':
 ***Fades (frames lost by individual sub-Rx)

@@ Line 11: / Line 11: @@
 **Calibrate and monitor you flight pack '''capacity used''' and set capacity alerts.
 ***Can be a reliable method to know pack condition.
 ***Best if you fly all packs of the same or very similar capacity.
 ***Set a transmitter alarm when a specified capacity is reached, then land on alarm.

@@ Line 27: / Line 27: @@
 ***Some may provide Rx bus (BEC) voltage, SPM4649T appears to not provide it
 **Provided by '''Betaflight/FLEXF3''':
-***Main Battery Pack (Main 3S) Voltage[[File:BF_SPM_Telem.jpg|thumb|upright=0.42|right|Telemetry 3-pin Connection]]
+***Main Battery Pack (Main 3S) Voltage[[File:BF_SPM_Telem.jpg|thumb|upright=0.42|right|Spektrum Telemetry 3-pin Connection]]
 ***Virtual (estimated) Current
 ***Virtual (estimated) Capacity used (fuel totalizer)

@@ Line 38: / Line 38: @@
 ***Make sure ''Serial Receiver Provider'' is set to '''''SPEKTRUM SRXL''''' (about the 10th choice down in the list)
 ***<big><strong>Now in ''Other Features'', '''set''' the ''TELEMETRY'' slider to '''''ON'''''.</strong></big>
-**On the '''Receiver''' page, make sure your ''Channel Map'' is set to '''''TAER1234''''' (SPEKTRUM/JR)
+**On the '''Receiver''' page, make sure your ''Channel Map'' is set to '''''TAER1234''''' (SPEKTRUM/Graupner)
 *You should now have Telemetry, and you can use your transmitters instructions and settings to display and alarm as desired.
 <br />

@@ Line 54: / Line 54: @@
 ==Jeti Telemetry==
-*These instructions supplement the non-telemetry setup instructions in the Cypher manual.
+*These instructions supplement the non-telemetry setup instructions in the Cypher manual and input Wiki.
 *Powerful and utilizes the Betaflight telemetry, but requires custom made cable.
 **Provided by '''Rx''':

@@ Line 57: / Line 57: @@
 *Powerful and utilizes the Betaflight telemetry, but requires custom made cable.
 **Provided by '''Rx''':
-***Radio Signal Data
+***Radio Signal Strength Data
 ***Receiver bus voltage (BEC)
 **Provided by '''Betaflight/FLEXF3''':

@@ Line 89: / Line 89: @@
 *Generally, JR DMSS does not interface with the Betaflight telemetry
 *Refer to your transmitter and receiver instructions for available options.
-**See the Futaba section above for voltage tap information
+**See the Futaba section above for general voltage tap information
 <br />
 <big><strong>[https://github.com/betaflight/betaflight/blob/master/docs/Telemetry.md Here is an External Link to Betaflights Telemetry information.]</strong></big><br />