FlexJetPro90/AuraFiles - Revision history

WikiSys at 15:20, 2 October 2025

2025-10-02T15:20:39Z

2021-03-24T18:59:05Z

‎Click a link below to Download the Aura Config file

2020-09-17T23:57:45Z

‎Special File Implementation Notes and Expert Tuning

2020-09-17T23:57:01Z

‎Special File Implementation Notes and Expert Tuning

2020-09-17T23:56:12Z

‎Special File Implementation Notes and Expert Tuning

2020-08-24T15:00:26Z

‎Click a link below to Download the Aura Config file

2020-08-24T14:56:40Z

‎Click a link below to Download the Aura Config file

2020-08-24T14:55:22Z

‎Click a link below to Download the Aura Config file

2020-08-24T13:18:46Z

‎Click a link below to Download the Aura Config file

2020-08-14T23:56:01Z

‎Click a link below to Download the Aura Config file

@@ Line 2: / Line 2: @@
 ==Click a link below to Download the Aura Config file==
-*[http://www.resources.flexinnovations.com/aura/auraConfigFiles/FlexJetPro_Aura_8S_Generic_V2.acf '''FlexJet Pro File for Standard Aura 8 (V2)'''] for Electric FlexJet Pro's
+*[http://resources.flexinnovations.com/aura/auraConfigFiles/FlexJetPro_Aura_8S_Generic_V2.acf '''FlexJet Pro File for Standard Aura 8 (V2)'''] for Electric FlexJet Pro's
-*[http://www.resources.flexinnovations.com/aura/auraConfigFiles/FlexJetPro_Aura_Pro_Generic.acf '''FlexJet Pro File for Aura Professionals'''] for Electric or Turbine FlexJet Pro's
+*[http://resources.flexinnovations.com/aura/auraConfigFiles/FlexJetPro_Aura_Pro_Generic.acf '''FlexJet Pro File for Aura Professionals'''] for Electric or Turbine FlexJet Pro's
 *[[FlexJetPro90/AuraFiles/AdvancedAura|'''Click here to go to a page with additional Files and Notes for ADVANCED AURA Users!''']]

@@ Line 6: / Line 6: @@
 *[[FlexJetPro90/AuraFiles/AdvancedAura|'''Click here to go to a page with additional Files and Notes for ADVANCED AURA Users!''']]
-'''NOTE:''' The '''Aura PRO file''' is set to use a '''Remote Sensor'''. In the case you are not using a '''Remote Sensor''', disable it in the config tool.
+'''NOTE:''' The '''Aura PRO file''' is set to use a '''Remote Sensor'''. In the case you are not using a '''Remote Sensor''', disable it in the config tool.<br />
 ==Transmitter Setting Tips when using Aura==

@@ Line 63: / Line 63: @@
 **''Aileron'' Data is copied to ''CH22'' using ''Aura Mix 3'' in Flight Modes 2 and 3 as Checked
 **''CH22'' Is added to the Stabs as 'Sources' in Servo Ports '''''S3''''' and '''''S4'''''.
-**Roll ‘’’Gyro’’’ inputs are NOT made to the Stabs, only Pitch Gyro inputs are put into the Stabs.
+**Roll '''Gyro''' inputs are NOT made to the Stabs, only Pitch Gyro inputs are put into the Stabs.
 **'''Tailerons''' free up the model to allow faster roll rates and a crisper response and improve roll response when Flaperons are used, but are not required. You could choose to disable them and increase the Aileron Travel a bit.
 *You can easily adjust your Flaperons' '''Flap''' travel and even flap transit speed using your '''Transmitter's''' features on ''CH6''

@@ Line 63: / Line 63: @@
 **''Aileron'' Data is copied to ''CH22'' using ''Aura Mix 3'' in Flight Modes 2 and 3 as Checked
 **''CH22'' Is added to the Stabs as 'Sources' in Servo Ports '''''S3''''' and '''''S4'''''.
-**Roll Gyro inputs are NOT made to the Stabs, only Pitch Gyro inputs are put into the Stabs.
+**Roll ‘’’Gyro’’’ inputs are NOT made to the Stabs, only Pitch Gyro inputs are put into the Stabs.
 **'''Tailerons''' free up the model to allow faster roll rates and a crisper response and improve roll response when Flaperons are used, but are not required. You could choose to disable them and increase the Aileron Travel a bit.
 *You can easily adjust your Flaperons' '''Flap''' travel and even flap transit speed using your '''Transmitter's''' features on ''CH6''

@@ Line 62: / Line 62: @@
 *'''Aileron''' transmitter roll input is put into the '''Horizontal Stabs''' (elevators) in ''Flight Modes'' 2 and 3 to make them '''Tailerons'''
 **''Aileron'' Data is copied to ''CH22'' using ''Aura Mix 3'' in Flight Modes 2 and 3 as Checked
 **''CH22'' Is added to the Stabs as 'Sources' in Servo Ports '''''S3''''' and '''''S4'''''.
-**Roll Gyro inputs and NOT made to the Stabs, only Pitch Gyro inputs are put into the Stabs.
+**Roll Gyro inputs are NOT made to the Stabs, only Pitch Gyro inputs are put into the Stabs.
-**'''Tailerons''' free up the model to allow faster roll rates and a crisper response and improve roll response when Flaperons are used, but are not required. You could choose to disable them and increase the Aileron Rates a bit.
+**'''Tailerons''' free up the model to allow faster roll rates and a crisper response and improve roll response when Flaperons are used, but are not required. You could choose to disable them and increase the Aileron Travel a bit.
 *You can easily adjust your Flaperons' '''Flap''' travel and even flap transit speed using your '''Transmitter's''' features on ''CH6''
 **Right and Left Flaps travel can be easily adjusted (independent of Aileron ''Output Scale/Travel'' with the Source2/CH6 ''Mix Scale'' values in Servo Ports '''''S1''''' and '''''S2'''''.