RV-8 60E G2/Crow - Revision history

WikiSys at 22:53, 30 June 2023

2023-06-30T22:53:52Z

WikiSys at 22:52, 30 June 2023

2023-06-30T22:52:57Z

WikiSys: Created page with "{{DISPLAYTITLE:How to Setup your RV-8 60E G2 Transmitter}} FORCETOC == Crow Quick Set Procedure..."

2023-06-30T22:45:17Z

Created page with "{{DISPLAYTITLE:How to Setup your RV-8 60E G2 Transmitter}} __FORCETOC__  == Crow Quick Set Procedure..."

New page

{{DISPLAYTITLE:How to Setup your RV-8 60E G2 Transmitter}}
__FORCETOC__ 
== Crow Quick Set Procedure for RV-8 60E G2 ==

To enter Quick Set mode, the Aura must receive a valid signal from the Receiver when the Aura is powered up.

Make sure your Transmitter is setup with your CH8/Aux3 channel assigned to a 2 Position switch for Crow.

=== Step 1 - Enter Quick Set mode ===
* Make sure all power is off on the RV-8 60E G2
** Remove the prop before making changes
* Turn on your transmitter
* Remove the Servo lead from Aura Port S2.
* Put a bind plug in Aura Port S2.
* Plug in the battery to power up the RV-8 60E G2
* The Orange LED will be OFF while the Green LED is ON indicating you are in the Quick Set mode and receiving a valid signal from the Receiver.

=== Step 2 - Choose Crow Option ===
After entering Quick Set mode as described above, toggle the CH8/Aux3 channel switch on the transmitter to ENABLE or DISABLE the Crow functionality.
* If the Red LED is on SOLID, Crow option is ENABLED in the Aura.
* If the Red LED is OFF, the Crow option is DISABLED in the Aura.

=== Step 3 - Save the desired Crow Option ===
# After correctly toggling the CH8/Aux3 switch to Enable or Disable the Crow option, '''remove the bind plug save the settings'''.
# The LEDs will turn on while the Aura is saving, then will go back to their previous state.
# Completely power off the RV-8 and Aura
# Replace the Servo Lead in Aura Port S2
# Power up, confirm that the Crow option can be be activated with your CH8/Aux3 Switch and Fly!

<noinclude>
[[Category:SuperPNP|Super PNP]]
[[Category:RV8|RV-8]]
</noinclude>

@@ Line 8: / Line 8: @@
 === Step 1 - Enter Quick Set mode ===
-* Make sure all power is off on the RV-8 60E G2
+# Make sure all power is off on the RV-8 60E G2
-** Remove the prop before making changes
+#* Remove the prop before making changes with Quick Set
-* Turn on your transmitter
+# Turn on your transmitter
-* Remove the Servo lead from Aura Port S2.
+# Remove the Servo lead from Aura Port S2.
-* Put a bind plug in Aura Port S2.
+# Put a bind plug in Aura Port S2.
-* Plug in the battery to power up the RV-8 60E G2
+# Plug in the battery to power up the RV-8 60E G2
-* The Orange LED will be OFF while the Green LED is ON indicating you are in the Quick Set mode and receiving a valid signal from the Receiver.
+# The Orange LED will be OFF while the Green LED is ON indicating you are in the Quick Set mode and receiving a valid signal from the Receiver.
 === Step 2 - Choose Crow Option ===
 After entering Quick Set mode as described above, toggle the CH8/Aux3 channel switch on the transmitter to ENABLE or DISABLE the Crow functionality.
-* If the Red LED is ON, the Crow option is ENABLED in the Aura.
+# If the Red LED is ON, the Crow option is ENABLED in the Aura.
-* If the Red LED is OFF, the Crow option is DISABLED in the Aura.
+# If the Red LED is OFF, the Crow option is DISABLED in the Aura.
 === Step 3 - Save the desired Crow Option ===

@@ Line 1: / Line 1: @@
-{{DISPLAYTITLE:How to Setup your RV-8 60E G2 Transmitter}}
+{{DISPLAYTITLE:How to Enable/Disable the Crow Switch using Quick Set from your Transmitter}}
 __FORCETOC__ <!-- This forces the Table of Contents since it has less than 3 levels -->
 == Crow Quick Set Procedure for RV-8 60E G2 ==
@@ Line 18: / Line 18: @@
 === Step 2 - Choose Crow Option ===
 After entering Quick Set mode as described above, toggle the CH8/Aux3 channel switch on the transmitter to ENABLE or DISABLE the Crow functionality.
-* If the Red LED is on SOLID, Crow option is ENABLED in the Aura.
+* If the Red LED is ON, the Crow option is ENABLED in the Aura.
 * If the Red LED is OFF, the Crow option is DISABLED in the Aura.
@@ Line 26: / Line 26: @@
 # Completely power off the RV-8 and Aura
 # Replace the Servo Lead in Aura Port S2
-# Power up, confirm that the Crow option can be be activated with your CH8/Aux3 Switch and Fly!
+# Power up, confirm that the Crow option can be activated with the CH8/Aux3 Switch and Fly!
 <noinclude>

RV-8 60E G2/Crow - Revision history

WikiSys at 22:53, 30 June 2023

WikiSys at 22:52, 30 June 2023

WikiSys: Created page with "{{DISPLAYTITLE:How to Setup your RV-8 60E G2 Transmitter}} __FORCETOC__ == Crow Quick Set Procedure..."

WikiSys: Created page with "{{DISPLAYTITLE:How to Setup your RV-8 60E G2 Transmitter}} FORCETOC == Crow Quick Set Procedure..."