Difference between revisions of "Cypher/Telemetry"
From Flex Innovations Wiki
| Line 32: | Line 32: | ||
**Follow the Futaba instruction to configure the Futaba equipment to display/alert with telemetry | **Follow the Futaba instruction to configure the Futaba equipment to display/alert with telemetry | ||
<br /> | <br /> | ||
| − | === | + | ===Jeti Telemetry=== |
| − | * | + | *Powerful, but requires custom made cable. |
**Provided by '''Rx''': | **Provided by '''Rx''': | ||
| − | *** | + | ***Radio Signal Data ?? |
| − | *** | + | ***Receiver bus voltage (BEC) ?? |
| − | + | ||
| − | + | ||
**Provided by '''Betaflight/FLEXF3''': | **Provided by '''Betaflight/FLEXF3''': | ||
***Main Battery Pack (Main 3S) Voltage | ***Main Battery Pack (Main 3S) Voltage | ||
***Virtual (estimated) Current | ***Virtual (estimated) Current | ||
***Virtual (estimated) Capacity used (fuel totalizer) | ***Virtual (estimated) Capacity used (fuel totalizer) | ||
| − | *Choose a telemetry capable receiver such as the | + | ***Horizon Angle in Pitch and Roll |
| + | *Choose a telemetry capable receiver such as the '''EX R3''' | ||
*Bind the receiver to the transmitter | *Bind the receiver to the transmitter | ||
| − | *<big><strong>Connect to '''FLEXF3''' using the first 3 pins (-,+,signal) | + | *Fabricate the Custom 3-pin to 4-pin male to male cable |
| − | *Use your configuration tool to: (hit the pages 'Save' button before | + | *<big><strong>Connect to '''FLEXF3''' using the first 3 pins (-,+,signal) at the Rx's UDI EX Bus Port and 4-pins at the FLEXF3 (-,+,Rx,Tx) </strong></big> |
| + | *Use your configuration tool to: (hit the pages 'Save' button before leaving each page)[[File:BF_Telemetry_F.jpg|thumb|upright=0.42|right|Set Telemetry Slider and Save]] | ||
**On '''Configuration''' page | **On '''Configuration''' page | ||
***Make sure ''Receiver Mode'' is set to a '''''serial based receiver'''''. | ***Make sure ''Receiver Mode'' is set to a '''''serial based receiver'''''. | ||
| − | ***Make sure ''Serial Receiver Provider'' is set to ''''' | + | ***Make sure ''Serial Receiver Provider'' is set to '''''JETIEXBUX''''' |
***<big><strong>Now in ''Other Features'', '''set''' the ''TELEMETRY'' slider to '''''ON'''''.</strong></big> | ***<big><strong>Now in ''Other Features'', '''set''' the ''TELEMETRY'' slider to '''''ON'''''.</strong></big> | ||
**On the '''Receiver''' page, make sure your ''Channel Map'' is set to '''''TAER1234''''' (SPEKTRUM) | **On the '''Receiver''' page, make sure your ''Channel Map'' is set to '''''TAER1234''''' (SPEKTRUM) | ||
*You should now have Telemetry, and you can use your transmitters instructions and settings to display and alarm as desired. | *You should now have Telemetry, and you can use your transmitters instructions and settings to display and alarm as desired. | ||
<br /> | <br /> | ||
Revision as of 14:01, 19 June 2019
Under Construction
Spektrum Telemetry
- Easy to setup (really just the third pin plug and telemetry slider in configurator) and provides the following Telemetry Data:
- Provided by Rx:
- Fades (frames lost by individual sub-Rx)
- Frames (frames of data lost buy all combined Rx)
- Holds (Failsafe caused buy more than 40 continuous Frame losses)
- Some may provide Rx bus (BEC) voltage, SPM4649T appears to not provide it
- Provided by Betaflight/FLEXF3:
- Main Battery Pack (Main 3S) Voltage
- Virtual (estimated) Current
- Virtual (estimated) Capacity used (fuel totalizer)
- Provided by Rx:
- Choose a telemetry capable receiver such as the SPM4649T (Preferred) or AR8010T
- Bind the receiver to the transmitter
- Connect to FLEXF3 using the first 3 pins (-,+,signal). (Use 3-male to 3-mail pin cable if required for AR8010T style receivers)
- Use your configuration tool to: (hit the pages 'Save' button before leavng each page)
- On Configuration page
- Make sure Receiver Mode is set to a serial based receiver.
- Make sure Serial Receiver Provider is set to SPEKTRUM2040/SRXL
- Now in Other Features, set the TELEMETRY slider to ON.
- On the Receiver page, make sure your Channel Map is set to TAER1234 (SPEKTRUM)
- On Configuration page
- You should now have Telemetry, and you can use your transmitters instructions and settings to display and alarm as desired.
Futaba Telemetry
- Only Telemetry provided by the Rx is available. Receivers are available that can sample Main Pack Voltage.
- Betaflight/FLEXF3 Data not available, so no Betaflight settings are made.
- Choose an S.Bus capable receiver (T-FHSS, FASSTest) that provides Telemetry and has a Voltage port (XXX, R7008SB FASSTest)
- "Y" or "Split" the small cable that provides Voltage Data to the FLEXF3. Install the Futaba compatible Voltage Cable/Plug to the voltage cable. (check polarity carefully!)
- Plug the voltage cable into the receiver
- Follow the Futaba instruction to configure the Futaba equipment to display/alert with telemetry
Jeti Telemetry
- Powerful, but requires custom made cable.
- Provided by Rx:
- Radio Signal Data ??
- Receiver bus voltage (BEC) ??
- Provided by Betaflight/FLEXF3:
- Main Battery Pack (Main 3S) Voltage
- Virtual (estimated) Current
- Virtual (estimated) Capacity used (fuel totalizer)
- Horizon Angle in Pitch and Roll
- Provided by Rx:
- Choose a telemetry capable receiver such as the EX R3
- Bind the receiver to the transmitter
- Fabricate the Custom 3-pin to 4-pin male to male cable
- Connect to FLEXF3 using the first 3 pins (-,+,signal) at the Rx's UDI EX Bus Port and 4-pins at the FLEXF3 (-,+,Rx,Tx)
- Use your configuration tool to: (hit the pages 'Save' button before leaving each page)
- On Configuration page
- Make sure Receiver Mode is set to a serial based receiver.
- Make sure Serial Receiver Provider is set to JETIEXBUX
- Now in Other Features, set the TELEMETRY slider to ON.
- On the Receiver page, make sure your Channel Map is set to TAER1234 (SPEKTRUM)
- On Configuration page
- You should now have Telemetry, and you can use your transmitters instructions and settings to display and alarm as desired.
