Difference between revisions of "RV-8 10E G2/GyroGainKill"
From Flex Innovations Wiki
(Created page with "{{DISPLAYTITLE:How to Enable/Disable the Gyro Gain Switch using Quick Set from your Transmitter}} __FORCETOC__ <!-- This forces the Table of Contents since it has less than 3...") |
m |
||
| Line 8: | Line 8: | ||
=== Step 1 - Enter Quick Set mode === | === Step 1 - Enter Quick Set mode === | ||
| − | # Make sure all power is off on the | + | # Make sure all power is off on the Airplane |
#* Remove the prop before making changes with Quick Set | #* Remove the prop before making changes with Quick Set | ||
# Turn on your transmitter | # Turn on your transmitter | ||
# Remove the Servo lead from Aura Port S2. | # Remove the Servo lead from Aura Port S2. | ||
# Put a bind plug in Aura Port S2. | # Put a bind plug in Aura Port S2. | ||
| − | # Plug in the battery to power up the | + | # Plug in the battery to power up the Airplane |
# The Orange LED will be OFF while the Green LED is ON indicating you are in the Quick Set mode and receiving a valid signal from the Receiver. | # The Orange LED will be OFF while the Green LED is ON indicating you are in the Quick Set mode and receiving a valid signal from the Receiver. | ||
| Line 24: | Line 24: | ||
# After correctly toggling the CH7/Aux2 switch to Enable or Disable the Gyro Gain Kill switch option, '''remove the bind plug save the settings'''. | # After correctly toggling the CH7/Aux2 switch to Enable or Disable the Gyro Gain Kill switch option, '''remove the bind plug save the settings'''. | ||
# The LEDs will turn on while the Aura is saving, then will go back to their previous state. | # The LEDs will turn on while the Aura is saving, then will go back to their previous state. | ||
| − | # Completely power off the | + | # Completely power off the Airplane and Aura |
# Replace the Servo Lead in Aura Port S2 | # Replace the Servo Lead in Aura Port S2 | ||
# Power up, confirm that the Gyro Gain Kill switch can kill the Gyro Gain with the CH7/Aux2 Switch and Fly! | # Power up, confirm that the Gyro Gain Kill switch can kill the Gyro Gain with the CH7/Aux2 Switch and Fly! | ||
Latest revision as of 00:15, 7 August 2025
Contents
Gyro Gain Kill Switch Quick Set Procedure for RV-8 10E G2
To enter Quick Set mode, the Aura must receive a valid signal from the Receiver when the Aura is powered up.
Make sure your Transmitter is setup with your CH7/Aux2 channel assigned to a 2 Position switch for the Gyro Gain Kill switch.
Step 1 - Enter Quick Set mode
- Make sure all power is off on the Airplane
- Remove the prop before making changes with Quick Set
- Turn on your transmitter
- Remove the Servo lead from Aura Port S2.
- Put a bind plug in Aura Port S2.
- Plug in the battery to power up the Airplane
- The Orange LED will be OFF while the Green LED is ON indicating you are in the Quick Set mode and receiving a valid signal from the Receiver.
Step 2 - Choose Gyro Gain Kill Switch Option
After entering Quick Set mode as described above, toggle the CH7/Aux2 channel switch on the transmitter to ENABLE or DISABLE the Gyro Gain Kill switch.
- If the Blue LED is ON, the Gyro Gain Kill switch option is ENABLED in the Aura.
- If the Blue LED is OFF, the Gyro Gain Kill switch option is DISABLED in the Aura.
Step 3 - Save the Gyro Gain Kill Switch Option
- After correctly toggling the CH7/Aux2 switch to Enable or Disable the Gyro Gain Kill switch option, remove the bind plug save the settings.
- The LEDs will turn on while the Aura is saving, then will go back to their previous state.
- Completely power off the Airplane and Aura
- Replace the Servo Lead in Aura Port S2
- Power up, confirm that the Gyro Gain Kill switch can kill the Gyro Gain with the CH7/Aux2 Switch and Fly!
