Aura/ConfigFiles

Aura Config Files by the Flex Innovations Team

Aura Config Files can be downloaded and saved to your PC. Use the Aura Config Tool to open the file. Each file can be reviewed and modified as needed.

For additional information, check Installing your Aura and Configuring your Aura. We currently support Spektrum, Futaba, Graupner, and JR Transmitters. For FR Sky, we recommend using our Custom FR Sky Transmitter File.

Do NOT fly any model without carefully checking the sensor and transmitter response. Servo Ports are labeled/named on the Servo Port Tab of the Aura Config Tool Application.

Flex Innovations Premier Aircraft Config Files

QQ Extra 300: Factory Aura Config File with Rx Auto Detect

• 3 Flight modes on CH5/Gear (0:Low Rate/Gain Off, 1:Low Rate/Low Gain/Precision, 2:High Rate/High Gain/3D)
• Master Gain is not enabled.
• Downloads:
  • Transmitter with Receiver Auto-Detect
  • Transmitter with Receiver Auto-Detect
  • Transmitter with Receiver Auto-Detect
  • Transmitter with Receiver Auto-Detect
  • X9D+ Transmitter with Receiver Auto-Detect

QQ Extra 300 Pro: Aura Config File with Rx Auto Detect and Master Gain

• 3 Flight modes on CH5/Gear (0:Low Rate/Gain Off, 1:Low Rate/Low Gain/Precision, 2:High Rate/High Gain/3D)
• Master Gain enabled on Ch8/Aux3 (Do not use if you are not controlling Ch8/Aux3).
• Center 3D Flight Mode gains are slightly higher than Factory Aura Config File
• Downloads:
  • Transmitter with Receiver Auto-Detect
  • Transmitter with Receiver Auto-Detect
  • Transmitter with Receiver Auto-Detect
  • Transmitter with Receiver Auto-Detect
  • X9D+ Transmitter with Receiver Auto-Detect

Ventique 60e Aura Config Files with Rx Auto Detect

• 3 Flight modes on CH5/Gear (0:Low Rate/Gain Off, 1:Low Rate/Low Gain/Precision, 2:High Rate/High Gain/3D)
• Master Gain is not enabled. (It is easy to assign in the Aura Config Tool)
• Quick Trim via BP S3: Enabled
• Quick Setup via BP S2: Disabled
• Downloads:
  • Transmitter with Receiver Auto-Detect
  • Transmitter with Receiver Auto-Detect
  • Transmitter with Receiver Auto-Detect
  • Transmitter with Receiver Auto-Detect
  • X9D+ Transmitter with Receiver Auto-Detect

Flex Innovations Premier Aircraft/BVM Config File

Yak 130 (P160 Turbine): Aura Config File with Powersafe SRXL Receiver

• Used with DX18 and AR12120 Rx using SRXL Data and a second power jumper to Aura.
• Set to Auto-Detect if SRXL data is not found.
• Flight Modes selected with CH11/XPlus1 assigned in Tx to the same switch as FLAPS.
• Master Gain is enabled with a rotary knob assigned to CH15/XPlus3.
• Gains increase as flaps are lowered
• Nose wheel steering uses inputs from Rudder (steering) with gain enabled and CH8/Aux3 (assigned to LTrmA) for trimming nose wheel (during taxi) while maintaining optimum gain.
• Aura subtrims (If you utilize this model, zero out the subtrim values in the Servo Ports Tab then apply new values as needed)
• Servo Port S8 is available as a 'channel expander' servo output with Ch17/XPlus5 data currently output
• Quick Trim via BP S3: Disabled Quick Setup via BP S2: Disabled
• Downloads:
  • Transmitter with AR12120 SRXL

Flex Innovations generated files - Additional Models

ParkZone Habu (foamie): Auto-Detects Digital Input

• Will auto-detect digital inputs or can be manually changed to other inputs such as diversity.
• Use Standard Aura Transmitter settings (per manual)
• Servo Ports: AilL, AilR, Elev, Rudd
• Can use Aileron Y-harness, or port for each Aileron as desired
• Includes an Aura mix: Rudder->Elevator for knife edge correction. Adjust as needed for your airframe.
• Flight Modes are switched with Ch5/Gear
• FM0: Uses CM-D. Middle Rates, Middle Gains. Uses Rate COMMAND control for Aileron instead of traditional Rate Dampener. Roll rate is sought with full gain throughout the stick range and seeks the commanded rate. The roll rate will be more consistent with changing airspeed.
  • You can assign Control Mode A (CM-A - no gyro) for test flying or as alternate
• FM1: Uses CM-B. Mid-Low Rates, Mid-Low Gains. All axis use traditional Rate Dampener controls
• FM2: Uses CM-C. Mid-High Rates, Mid-High Gains. All axis use traditional Rate Dampener controls
• Master gain is active on Ch8/Aux3 (can be disbled in App)
• Check subtrims on the Servo Port tab in the app and adjust as needed. Quick Trims can be used after test flight.
• For this type of flying, you can add in some transmitter Low Rates if desired to have more options available.
• Custom Aura orientation in Model/App. Adjust as needed.
• Quick Setup via BP S2: Disabled Quick Trim via BP S3: Enabled
• Downloads:
  • Habu Aura File