Difference between revisions of "FlexJet/LatestUpdates"
From Flex Innovations Wiki
(→Build Tips) |
|||
| Line 18: | Line 18: | ||
*Per the manual insert, please set your transmitter '''CH5/Gear Travel''' to '''+-125%''' to ensure the '''Gear Sequencer''' will follow the transmitter and function properly. | *Per the manual insert, please set your transmitter '''CH5/Gear Travel''' to '''+-125%''' to ensure the '''Gear Sequencer''' will follow the transmitter and function properly. | ||
[[File:Stab_Fairing_5029.jpg|thumb|upright=0.5|right|Side Fairing Installation]] | [[File:Stab_Fairing_5029.jpg|thumb|upright=0.5|right|Side Fairing Installation]] | ||
| + | *'''FlexJet G2 Wing Installation''' | ||
| + | **The G2 has tubes in the fuselage to accept the wing spars. It is possible that there could be a little residual glue outside near the plywood rib, or a slight misalignment of the plywood rib to the tube. This could make it difficult to insert the Wing Tubes into the Fuselage. | ||
| + | **Test fit the Wing Tubes into the Fuselage using a twisting motion as needed. If it is to difficult to inserted, use a #11 hobby knife to clean the plywood rib and the opening of the receptacle. | ||
| + | **Once the wing tubes are installed in the fuselage, slide the Wing Panels onto the tubes and finish securing the Wing. | ||
*The '''Stab Linkage''' is located on the Outer-most hole from center at the '''Stab Arm End''' (aft end). Check/Connect the Clevis/Pushrod to the '''Stab Arm'''. | *The '''Stab Linkage''' is located on the Outer-most hole from center at the '''Stab Arm End''' (aft end). Check/Connect the Clevis/Pushrod to the '''Stab Arm'''. | ||
*The '''Stab Linkage''' is located the 2nd hole from the center at the '''Servo End'''. Attach the Stab Linkage to the '''Servo Arm'''. | *The '''Stab Linkage''' is located the 2nd hole from the center at the '''Servo End'''. Attach the Stab Linkage to the '''Servo Arm'''. | ||
Revision as of 20:27, 28 May 2021
Contents
Latest Updates
Printed Manual Typo
None - See below
Latest Online Manual
The Latest Version of the FlexJet Manual (Rev - 1.0) is available online.
- This version matches the printed manual. (See add-in note on Gear Travel below)
- See Build Tips below for minor updates.
Build Tips
Initial Build
- The AR8010T or AR6610T are our highest recommended Spektrum Receivers for the FlexJet G1/G2.
- For Futaba users, our highest recommended FASST receiver is the R7008SB or R6303SB. For FHSS, the R2008SB.
- Per the manual insert, please set your transmitter CH5/Gear Travel to +-125% to ensure the Gear Sequencer will follow the transmitter and function properly.
- FlexJet G2 Wing Installation
- The G2 has tubes in the fuselage to accept the wing spars. It is possible that there could be a little residual glue outside near the plywood rib, or a slight misalignment of the plywood rib to the tube. This could make it difficult to insert the Wing Tubes into the Fuselage.
- Test fit the Wing Tubes into the Fuselage using a twisting motion as needed. If it is to difficult to inserted, use a #11 hobby knife to clean the plywood rib and the opening of the receptacle.
- Once the wing tubes are installed in the fuselage, slide the Wing Panels onto the tubes and finish securing the Wing.
- The Stab Linkage is located on the Outer-most hole from center at the Stab Arm End (aft end). Check/Connect the Clevis/Pushrod to the Stab Arm.
- The Stab Linkage is located the 2nd hole from the center at the Servo End. Attach the Stab Linkage to the Servo Arm.
- The free Stab end Arm and Clevis can be turned together to make pushrod length adjustments while checking. Screw the Arm in place after correct trim is confirmed. (as described in Manual P. 11, Step 5)
- It is likely that your Ventral Fins are already installed, so you may not have to install these per the manual.
- Your Side Fairings behind the stab are likely NOT installed (change to prevent shipping damage). They are likely packed with your missile rails. Please glue them onto the aft fuselage with CA or Epoxy before installing the tail cone.
- Please check the glue joints of the Rib in the fuselage socket where the wing attaches. Add some medium CA as needed. There have been several reports of inadequate glue.
- When re-installing the Tailpipe, a good technique is to get the tailpipe aligned with the back edge of the fan as close as possible, then 'pop' the aft end of the tailpipe with the open palm of your hand and it will 'jump' forward into place.
Click to view a Stab/Tailpipe Instructional Video on YouTube
Full Build Video
Click to view the Full Build Instructional Video on YouTube
Timeline for specific segments of this video!
(Go to YouTube Page and you will have links)
Introduction - 0:00
Required Tools and Accessories - 0:52
Spektrum Transmitter Setup - 2:02
Spektrum Receiver Installation - 6:23
Futaba Transmitter Setup - 10:07
Futaba Receiver Installation - 17:20
Removal of Tail Pipe and Exhaust Nozzle - 20:51
Horizontal Stabilizer Installation - 23:22
Main Wing Installation - 32:00
Vertical Fin Installation - 35:57
Tail Pipe and Nozzle Installation - 44:50
Missile Rail Installation - 50:14
Pre-Flight Checks - 51:10
Outro - 53:00
General Tips
- It is possible to scrape the ventral fins and tail cone on the ground on landing. You can put a couple of layers of clear tape on the bottom of these to reduce wear
- As described in the manual (P. 9, Top), Arm the retracts before each flight.
- Please read the Quick Trim section of the manual carefully, noting it has the ability to fine tune the Stab Trim in pitch and roll Before and/or After flying.
Aura Tips
- For Aura new comers, note that ANY Aura servo port (ex. Nose Wheel Steering) can be subtrimmed using the Aura Config Tool (set View->Advanced). Config Tool->Servo Ports->Subtrim. Be sure to WRITE to Aura to utilize the new settings. Most other parameters can also be adjusted in the Aura Config Tool
- For Aura veterans, please note that the FlexJet uses Ch5/Gear for Retracts (2 position switch preferred), and Ch6/Aux1 for Aura Flight Modes (3 position switch preferred). This is different than most of the previous 5 channel SPNP planes.
Please consult the FlexJet Manual for Build instructions.
Addendum
See Retract Sequencer, Fairing Attachment, and other notes. -Above-
Parts Notes
- The Left Main Landing Gear Door uses the NORMAL direction servo. FPZDS12
- The Right Main Landing Gear Door and Nose Door use the REVERSE direction servo. FPZDS12R
- The Nose Wheel Steering uses the REVERSE direction servo. FPZDS12R
- See the Part List Here
