Revision as of 19:02, 13 August 2020

Aura Files and Help

As always with Aura... Wing and Tail Type is Normal. 1 Aileron, 1 Elevator, 1 Rudder, 1 Flap
- Flaperon mixing will be done by Aura
Use Receiver with working Throttle Port. Throttle is plugged into Receiver.
CH5 is reserved for Retract Use via Receiver Port (set 2-position switch)
CH6 is the Flap 'data' that Aura will Mix into Flaperons. Use land system if available. (set 3 (or 2) position switch)
CH7 is reserved for Wheel Brakes, Use via Receiver Port. We use a SLIDER or other proportional input for Brakes. You could select a different channel as needed.
CH8 is reserved for Master Gain (but is NOT enabled in Control Modes (set proportional knob or slider if desired, and enable in Control Modes) CH8 could be re-assigned if not used for Master Gain.
CH9 is used for Flight Mode Change (Could be changed to CH7 for example (if not using Wheel Brakes) on the Setup Tab (set 3-position switch)

Download the appropriate file for your Aura and move it to a known directory on your PC
Open the Aura Config Tool (update tool if update is available)
- Please make sure your Aura Firmware is v1.14 or newer
Open the Aura Config File (.acf) from the saved location.
On the Setup Tab, select your Radio Brand and Protocol and Connection Port.
Verify that the Orientation of the Aura is as-set on the Setup Tab, Adjust as needed.
Save your file.
Write all to Aura
Power up and adjust settings in Servo Ports as needed
- Reversing may be needed depending on Servo Brand, etc.
- Subtrim will likely be needed.
- You can tweak Output Scale (travel) as needed to make surfaces move symmetrically/equally
- Perform and pass all Control and Sensor Tests

The nosewheel is coupled specifically to allow it to be turned OFF when the Gear is UP
- Rudder Channel Data is mixed to CH21 insider Aura via Aura Mix 1
  - This mix is turned ON and OFF via the CH5/Gear
  - If Reversing the Gear is necessary (Steering is working when UP instead of DOWN), you may need to change the Switch Position where the Mix is ACTIVE vs. INACTIVE inside Aura Mix 1!
- CH21 Steering Data is then output on Servo Port S6 for Steering Servo

@@ Line 8: / Line 8: @@
 *As always with Aura... Wing and Tail Type is Normal. 1 Aileron, 1 Elevator, 1 Rudder, 1 Flap
 **Flaperon mixing will be done by Aura
-*Use Receiver with working Throttle Port. Throttle is plugged into Receiver.
+*Use Receiver with working Throttle Port. Throttle is plugged into '''Receiver'''.
-*CH5 is reserved for ''Retract'' Use via Receiver Port (set 2-position switch)
+*CH5 is reserved for ''Retract'' Use via '''Receiver Port''' (set 2-position switch)
 *CH6 is the ''Flap'' 'data' that '''Aura''' will Mix into Flaperons. Use land system if available. (set 3 (or 2) position switch)
-*CH8 is reserved for ''Master Gain'' (but is NOT enabled in ''Control Modes'' (set proportional knob or slider if desired, and enable in Control Modes)
+*CH7 is reserved for ''Wheel Brakes'', Use via '''Receiver Port'''. We use a SLIDER or other proportional input for Brakes. You could select a different channel as needed.
-*CH9 is used for ''Flight Mode Change'' (Could be changed to CH7 for example on ''Setup Tab'' (set 3-position switch)
+*CH8 is reserved for ''Master Gain'' (but is NOT enabled in ''Control Modes'' (set proportional knob or slider if desired, and enable in Control Modes) CH8 could be re-assigned if not used for Master Gain.
+*CH9 is used for ''Flight Mode Change'' (Could be changed to CH7 for example (if not using Wheel Brakes) on the ''Setup Tab'' (set 3-position switch)
 ==General Aura Guidelines for File Use.==