Difference between revisions of "FlexJet Pro/TurbineConversion"
(→Fuel System Components) |
(→Fuel System Components) |
||
| Line 30: | Line 30: | ||
== Fuel System Components == | == Fuel System Components == | ||
*Setup your fuel system in a fashion compatible with your turbine manufacturer's instructions. | *Setup your fuel system in a fashion compatible with your turbine manufacturer's instructions. | ||
| − | *Flex Innovations used [https://www.chiefaircraft.com/map-mini-2oz-at.html this 2oz UAT] and the equipment tray accommodates it. | + | *Flex Innovations used [https://www.chiefaircraft.com/map-mini-2oz-at.html this '''2oz UAT'''] and the equipment tray accommodates it. |
**A UAT eliminates air bubbles going to the fuel pump/turbine. An excellent fuel system required for reliable engine operations! Take great care. | **A UAT eliminates air bubbles going to the fuel pump/turbine. An excellent fuel system required for reliable engine operations! Take great care. | ||
| − | *A 6oz Sullivan Flex Slant Tank was used as the Collector Tank (the Flex allows slight deformation of the tank for a relaxed fit) | + | *A '''6oz Sullivan Flex Slant Tank''' was used as the Collector Tank (the Flex allows slight deformation of the tank for a relaxed fit) |
**The Collector tanks takes the fuel from the main tank before delivering it to the UAT. It adds capacity and also buffers air-bubbles from the long main tank. | **The Collector tanks takes the fuel from the main tank before delivering it to the UAT. It adds capacity and also buffers air-bubbles from the long main tank. | ||
| − | **A 4oz non-flex Slant Tank could also be used | + | **A '''4oz non-flex Slant Tank''' could also be used |
| − | *Main Tank Choices | + | *'''Main Tank Choices''' |
| − | **A cost effective but smaller option is the Sullivan 24oz Slant Tank. It fits and works well. | + | **A cost effective but smaller option is the '''Sullivan 24oz Slant Tank'''. It fits and works well. |
| − | **Flex innovations is working on a Custom Composite 35oz | + | **Flex innovations is working on a '''Custom Composite 35oz Tank''' for the best flight time. |
== Reinforced the Battery Tray == | == Reinforced the Battery Tray == | ||
Revision as of 18:47, 8 July 2020
Contents
FlexJet Pro Turbine Conversion
The FlexJet Pro was designed with turbine conversion in mind. The inlet was routed down to provide ample space for a fuel cell. The forward equipment tray was made removable so an alternate could be installed. The Tailcone is removeable to ease component installation.
The FlexJet Pro on a 4.5kg offers and excellent turbine experience. It gives an aerobatic 'fast jet' experience while never feeling heavy. Power is impressive and never lacking.
Flight time can vary depending on fuel tank install and flying style. The K-45 G3 flies about 4:20 with the 24oz main tank, and beyond 5:30 with the 34oz main tank. These times allow for startup, and ample reserves for a go around.
The primary conversion involves installing the turbine mounts and turbine. Installing the tailpipe, Assembling and installing the fuel tanks, and equipping and installing the forward equipment tray.
Turbine aircraft should be fitted with Wheel Brakes. These are drop in units!
NOTE: that KingTech recommends running the engine outside the model with the assembled equipment tray and fuel system. Flex Innovations used this procedure and had complete success.
Turbine Selection
- At the time of this writing, Flex Innovations has tested the KingTech K45 G3 and have found it to be a perfect match.
- The Zicoy X45 is very similar, and its mounting was considered in the design. It should be easily fitted as well.
- Flex Innovations in no way recommends turbines with greater than 4.5kg thrust.
- Turbines have very high exhaust gas velocities and can reach high speeds. Throttle management should be used.
Battery Selection
- Flight Pack (aka Radio) Batteries (2S LiPo)
- A single 2S 2000mAh 15C Lipo is a good choice When using a gyro-less setup, or when using the Aura Professional.
- Dual 2S 1400mAh+ batteries would also be a good choice, and the Aura Professional can connect them in and ideal fashion.
- Turbine (aka ECU) Battery (Follow your Turbine manufacturer's recommendations)
- The KingTech K45 G3 recommends a 3S LiFe
- Flex Innovations used the 3S 2200mAh LiFe from Spektrum.
- KingTech also sells a 3S LiPo you could choose.
- The KingTech K45 G3 recommends a 3S LiFe
Fuel System Components
- Setup your fuel system in a fashion compatible with your turbine manufacturer's instructions.
- Flex Innovations used this 2oz UAT and the equipment tray accommodates it.
- A UAT eliminates air bubbles going to the fuel pump/turbine. An excellent fuel system required for reliable engine operations! Take great care.
- A 6oz Sullivan Flex Slant Tank was used as the Collector Tank (the Flex allows slight deformation of the tank for a relaxed fit)
- The Collector tanks takes the fuel from the main tank before delivering it to the UAT. It adds capacity and also buffers air-bubbles from the long main tank.
- A 4oz non-flex Slant Tank could also be used
- Main Tank Choices
- A cost effective but smaller option is the Sullivan 24oz Slant Tank. It fits and works well.
- Flex innovations is working on a Custom Composite 35oz Tank for the best flight time.
Reinforced the Battery Tray
Thin and medium CA Glue was used for all. See Images
- Approximately 1/2 wide strips of Carbon plate (~.080" thick) was used in two places to reinforce the structure under the tray. It was wrapped to the structure with carbon chord (tow).
- At the aft end under the battery tray oriented vertically. Carbon chord wraps used.
- At the middle of the tray oriented flat against the bottom of the tray. Carbon chord wraps used.
- Two strips of Carbon plate were laminated to the top of the tray to stiffen it and to apply velcro® to.
- The aft edge of the plates were thinned to allow carbon chord wraps to be applied to prevent delamination.
- A hole were made in the front center of each plate, and the plated was wrapped to the existing structure with carbon chord to prevent delamination.
- Holes and slots were made in the tray to allow for carbon wraps, and velcro® straps
Motor and ESC
Tray Preparations
Tray Preparations
1 of 2 Carbon Strips
Strip in Middle
Aft Wraps
Overview
Aft Wraps
Middle Wraps
Middle Wraps
Radio Tray
