Difference between revisions of "Mamba 60/LatestUpdates"
From Flex Innovations Wiki
(→Addendum) |
(→Addendum) |
||
| Line 9: | Line 9: | ||
*It was found that the factory improperly configured the aileron servo extensions in the Aura 8. Check and verify that your servo extensions are plugged in to the ports as shown below. If they are not configured in this way, remove them from the Aura and configure them accordingly. This is also shown properly on Page 11 of the instruction manual. | *It was found that the factory improperly configured the aileron servo extensions in the Aura 8. Check and verify that your servo extensions are plugged in to the ports as shown below. If they are not configured in this way, remove them from the Aura and configure them accordingly. This is also shown properly on Page 11 of the instruction manual. | ||
**S1 - Throttle (ESC/BEC), if applicable* | **S1 - Throttle (ESC/BEC), if applicable* | ||
| + | ***Only use throttle in S1 if your receiver does not have a functioning throttle port. | ||
**S2 - Left, Top Aileron | **S2 - Left, Top Aileron | ||
**S3 - Left, Bottom Aileron | **S3 - Left, Bottom Aileron | ||
| Line 16: | Line 17: | ||
**S7 - Rudder | **S7 - Rudder | ||
**S8 - LED Controller (if applicable to your version). | **S8 - LED Controller (if applicable to your version). | ||
| − | + | ||
*It was found that the Wing Type listed in the Transmitter Configuration Guide on page 9 of the instruction manual was incorrect. Please select 1 aileron, 1 elevator, 1 rudder as the wing type in your transmitter. | *It was found that the Wing Type listed in the Transmitter Configuration Guide on page 9 of the instruction manual was incorrect. Please select 1 aileron, 1 elevator, 1 rudder as the wing type in your transmitter. | ||
*It was found that the main wing mounting screws listed on page 24 of the instruction manual are incorrect. The proper wing mounting screws are (4) M3x10 Phillips head machine screws, included in a bag labeled Main Wing. | *It was found that the main wing mounting screws listed on page 24 of the instruction manual are incorrect. The proper wing mounting screws are (4) M3x10 Phillips head machine screws, included in a bag labeled Main Wing. | ||
Revision as of 13:07, 26 July 2019
Latest Updates
Latest Online Manual
The Latest Version of the Mamba 60E+ Manual is available online.
- This version matches the printed manual at this time.
Addendum
The manual addendum and Aura connection document can be found here: Mamba 60E Addendum
- It was found that the factory improperly configured the aileron servo extensions in the Aura 8. Check and verify that your servo extensions are plugged in to the ports as shown below. If they are not configured in this way, remove them from the Aura and configure them accordingly. This is also shown properly on Page 11 of the instruction manual.
- S1 - Throttle (ESC/BEC), if applicable*
- Only use throttle in S1 if your receiver does not have a functioning throttle port.
- S2 - Left, Top Aileron
- S3 - Left, Bottom Aileron
- S4 - Right, Top Aileron
- S5 - Right, Bottom Aileron
- S6 - Elevator
- S7 - Rudder
- S8 - LED Controller (if applicable to your version).
- S1 - Throttle (ESC/BEC), if applicable*
- It was found that the Wing Type listed in the Transmitter Configuration Guide on page 9 of the instruction manual was incorrect. Please select 1 aileron, 1 elevator, 1 rudder as the wing type in your transmitter.
- It was found that the main wing mounting screws listed on page 24 of the instruction manual are incorrect. The proper wing mounting screws are (4) M3x10 Phillips head machine screws, included in a bag labeled Main Wing.
Build Tips
- Ensure that the wing tubes fully seat into each wing. If the wing tubes come to a hard, audible, wood-like stop, you still have about 1/4-inch further to insert the wing tube into the wing. The wing tube stops against foam material, not wood. The wood material at the tip of the tube is the last ring that the wing tube needs to pass through.
- The cabane struts can be left unglued if transportation is an issue, but for better longevity, we highly recommend gluing the cabane struts in place with 15-minute epoxy. (Page 16 of the instruction manual)
