Difference between revisions of "RV-8 60E G2/GyroGainKill"

From Flex Innovations Wiki
Jump to: navigation, search
m
m
 
Line 8: Line 8:
  
 
=== Step 1 - Enter Quick Set mode ===
 
=== Step 1 - Enter Quick Set mode ===
−
* Make sure all power is off on the RV-8 60E G2
+
# Make sure all power is off on the RV-8 60E G2
−
** Remove the prop before making changes  
+
#* Remove the prop before making changes with Quick Set
−
* Turn on your transmitter
+
# Turn on your transmitter
−
* Remove the Servo lead from Aura Port S2.
+
# Remove the Servo lead from Aura Port S2.
−
* Put a bind plug in Aura Port S2.
+
# Put a bind plug in Aura Port S2.
−
* Plug in the battery to power up the RV-8 60E G2
+
# Plug in the battery to power up the RV-8 60E G2
−
* The Orange LED will be OFF while the Green LED is ON indicating you are in the Quick Set mode and receiving a valid signal from the Receiver.
+
# The Orange LED will be OFF while the Green LED is ON indicating you are in the Quick Set mode and receiving a valid signal from the Receiver.
  
 
=== Step 2 - Choose Gyro Gain Kill Switch Option ===
 
=== Step 2 - Choose Gyro Gain Kill Switch Option ===
 
After entering Quick Set mode as described above, toggle the CH7/Aux2 channel switch on the transmitter to ENABLE or DISABLE the Gyro Gain Kill switch.
 
After entering Quick Set mode as described above, toggle the CH7/Aux2 channel switch on the transmitter to ENABLE or DISABLE the Gyro Gain Kill switch.
−
* If the Blue LED is ON, the Gyro Gain Kill switch option is ENABLED in the Aura.
+
# If the Blue LED is ON, the Gyro Gain Kill switch option is ENABLED in the Aura.
−
* If the Blue LED is OFF, the Gyro Gain Kill switch option is DISABLED in the Aura.
+
# If the Blue LED is OFF, the Gyro Gain Kill switch option is DISABLED in the Aura.
  
 
=== Step 3 - Save the Gyro Gain Kill Switch Option ===
 
=== Step 3 - Save the Gyro Gain Kill Switch Option ===

Latest revision as of 22:54, 30 June 2023


Gyro Gain Kill Switch Quick Set Procedure for RV-8 60E G2

To enter Quick Set mode, the Aura must receive a valid signal from the Receiver when the Aura is powered up.

Make sure your Transmitter is setup with your CH7/Aux2 channel assigned to a 2 Position switch for the Gyro Gain Kill switch.

Step 1 - Enter Quick Set mode

  1. Make sure all power is off on the RV-8 60E G2
    • Remove the prop before making changes with Quick Set
  2. Turn on your transmitter
  3. Remove the Servo lead from Aura Port S2.
  4. Put a bind plug in Aura Port S2.
  5. Plug in the battery to power up the RV-8 60E G2
  6. The Orange LED will be OFF while the Green LED is ON indicating you are in the Quick Set mode and receiving a valid signal from the Receiver.

Step 2 - Choose Gyro Gain Kill Switch Option

After entering Quick Set mode as described above, toggle the CH7/Aux2 channel switch on the transmitter to ENABLE or DISABLE the Gyro Gain Kill switch.

  1. If the Blue LED is ON, the Gyro Gain Kill switch option is ENABLED in the Aura.
  2. If the Blue LED is OFF, the Gyro Gain Kill switch option is DISABLED in the Aura.

Step 3 - Save the Gyro Gain Kill Switch Option

  1. After correctly toggling the CH7/Aux2 switch to Enable or Disable the Gyro Gain Kill switch option, remove the bind plug save the settings.
  2. The LEDs will turn on while the Aura is saving, then will go back to their previous state.
  3. Completely power off the RV-8 and Aura
  4. Replace the Servo Lead in Aura Port S2
  5. Power up, confirm that the Gyro Gain Kill switch can kill the Gyro Gain with the CH7/Aux2 Switch and Fly!
Retrieved from "https://wiki.flexinnovations.com/index.php?title=RV-8_60E_G2/GyroGainKill&oldid=5842"