Difference between revisions of "RV-8 60E G2/TransmitterSetup"
From Flex Innovations Wiki
(Created page with "{{DISPLAYTITLE:How to Setup your RV-8 60E G2 Transmitter}} __FORCETOC__ <!-- This forces the Table of Contents since it has less than 3 levels --> == RV-8 60E G2 Transmitter S...") |
m |
||
Line 1: | Line 1: | ||
{{DISPLAYTITLE:How to Setup your RV-8 60E G2 Transmitter}} | {{DISPLAYTITLE:How to Setup your RV-8 60E G2 Transmitter}} | ||
− | + | __NOTOC__ <!-- This forces the Table of Contents since it has less than 3 levels --> | |
− | == RV-8 60E G2 Transmitter | + | == How to Setup your RV-8 60E G2 Transmitter Model == |
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
+ | === Transmitter Model Setup Procedure === | ||
+ | # Create a Blank Transmitter Airplane Model with 1 Throttle, 1 Aileron, 1 Elevator, 1 Rudder and any Flaps or Flap System OFF. | ||
+ | # Assign the Transmitter's Ch5/Gear channel to a 3 Position switch to change the Flight Modes in flight | ||
+ | # Assign the Transmitter's CH6/Aux1 Channel to a 3 Position switch to control the Flaps in flight | ||
+ | # (Optional) Assign the Transmitter's Ch7/Aux2 Channel to a 2 Position switch to function as a Gyro Gain Kill switch in flight | ||
+ | #* The Gyro Gain Kill functionality is initially Disabled by default, [[RV-8_60E_G2/GyroGainKill|but can be Enabled using Quick Set with your Transmitter]] | ||
+ | # (Optional) Assign the Transmitter's Ch8/Aux3 Channel to a 2 Position switch to function as a Crow switch in flight | ||
+ | #* The Crow functionality is intially Disabled by default, [[RV-8_60E_G2/Crow|but can be Enabled using Quick Set with your Transmitter]] | ||
+ | # Adjust Aileron, Elevator, Rudder and Throttle End Points (aka Travel Limits or ATV) as shown in the table below for your Transmitter brand | ||
+ | # Verify the rest of the settings as shown in the table below for your Transmitter brand | ||
Line 26: | Line 31: | ||
| '''Trim Levers''' || colspan=3 | Verify at Zero | | '''Trim Levers''' || colspan=3 | Verify at Zero | ||
|- | |- | ||
− | | '''CH5 (Gear) | + | | '''Flight Mode Switch - CH5 (Gear)''' || colspan=3 | Assign the CH5/Gear channel to a 3 Position switch |
|- | |- | ||
− | | '''CH6 (Aux1) | + | | '''Flap Switch - CH6 (Aux1)''' || colspan=3 | Assign the CH6/Aux1 channel to a 3 Position switch<br>Do NOT use Transmitter Flap System. Flap Values are pre-programmed into the Aura. |
|- | |- | ||
− | | ''' | + | | '''Gyro Gain Kill Switch - CH7/Aux2**'''|| colspan=3 | Assign the CH7/Aux2 channel to a 2 Position switch (Optional) |
|- | |- | ||
− | | '''CH8 | + | | '''Crow Switch - CH8/Aux3**''' || colspan=3 | Assign the CH8/Aux3 channel to a 2 Position switch to a 2 Position Switch (Optional) |
|- | |- | ||
| '''First Flight Timer'''|| colspan=3 | For your first flight, set to 5:30 | | '''First Flight Timer'''|| colspan=3 | For your first flight, set to 5:30 | ||
|} | |} | ||
− | '''<nowiki> * </nowiki>''' - The Gyro Gain Kill Switch and Crow options are initially Disabled and can be Enabled using Quick Set from your Transmitter as detailed below | + | '''<nowiki> ** </nowiki>''' - The Gyro Gain Kill Switch and Crow options are initially Disabled and can be Enabled using Quick Set from your Transmitter as detailed below |
+ | |||
+ | |||
== RV-8 60E G2 Options == | == RV-8 60E G2 Options == | ||
* [[RV-8_60E_G2/Crow|How to use Enable Crow with QuickSet from your Transmitter]] | * [[RV-8_60E_G2/Crow|How to use Enable Crow with QuickSet from your Transmitter]] | ||
* [[RV-8_60E_G2/GyroGainKill|How to use Enable Gyro Gain Kill Switch with QuickSet from your Transmitter]] | * [[RV-8_60E_G2/GyroGainKill|How to use Enable Gyro Gain Kill Switch with QuickSet from your Transmitter]] | ||
+ | |||
== Basic Super PNP Transmitter Setup Video == | == Basic Super PNP Transmitter Setup Video == | ||
+ | {{#ev:youtube|https://youtu.be/ep0a78QopDc||left|Basic Super PNP Transmitter Setup shown here as a reference }} | ||
<noinclude> | <noinclude> |
Revision as of 22:11, 30 June 2023
How to Setup your RV-8 60E G2 Transmitter Model
Transmitter Model Setup Procedure
- Create a Blank Transmitter Airplane Model with 1 Throttle, 1 Aileron, 1 Elevator, 1 Rudder and any Flaps or Flap System OFF.
- Assign the Transmitter's Ch5/Gear channel to a 3 Position switch to change the Flight Modes in flight
- Assign the Transmitter's CH6/Aux1 Channel to a 3 Position switch to control the Flaps in flight
- (Optional) Assign the Transmitter's Ch7/Aux2 Channel to a 2 Position switch to function as a Gyro Gain Kill switch in flight
- The Gyro Gain Kill functionality is initially Disabled by default, but can be Enabled using Quick Set with your Transmitter
- (Optional) Assign the Transmitter's Ch8/Aux3 Channel to a 2 Position switch to function as a Crow switch in flight
- The Crow functionality is intially Disabled by default, but can be Enabled using Quick Set with your Transmitter
- Adjust Aileron, Elevator, Rudder and Throttle End Points (aka Travel Limits or ATV) as shown in the table below for your Transmitter brand
- Verify the rest of the settings as shown in the table below for your Transmitter brand
Spektrum, Futaba, JR & Graupner | FrSky | Jeti (EX-Bus) | |
---|---|---|---|
Wing/Tail Type | 1 Aileron, 1 Elevator, 1 Rudder | 1 Aileron, 1 Elevator, 1 Rudder | 1 Aileron, 1 Elevator, 1 Rudder |
End Points (Travel Adjust or ATV) | Ail/Ele/Rud: 125% | Ail/Ele/Rud: 100% | Ail/Ele/Rud: 100% |
Throttle End Points (Travel Adjust or ATV) | Thr: 100% | Thr: 84% | Thr: 80% |
Reversing | Not Allowed | ||
Sub-Trim | Verify at Zero, NOT ALLOWED | ||
Trim Levers | Verify at Zero | ||
Flight Mode Switch - CH5 (Gear) | Assign the CH5/Gear channel to a 3 Position switch | ||
Flap Switch - CH6 (Aux1) | Assign the CH6/Aux1 channel to a 3 Position switch Do NOT use Transmitter Flap System. Flap Values are pre-programmed into the Aura. | ||
Gyro Gain Kill Switch - CH7/Aux2** | Assign the CH7/Aux2 channel to a 2 Position switch (Optional) | ||
Crow Switch - CH8/Aux3** | Assign the CH8/Aux3 channel to a 2 Position switch to a 2 Position Switch (Optional) | ||
First Flight Timer | For your first flight, set to 5:30 |
** - The Gyro Gain Kill Switch and Crow options are initially Disabled and can be Enabled using Quick Set from your Transmitter as detailed below
RV-8 60E G2 Options
- How to use Enable Crow with QuickSet from your Transmitter
- How to use Enable Gyro Gain Kill Switch with QuickSet from your Transmitter