Difference between revisions of "RV-8 60E G2/TransmitterSetup"
From Flex Innovations Wiki
m |
m |
||
| Line 29: | Line 29: | ||
| '''Trim Levers''' || colspan=3 | Verify at Zero | | '''Trim Levers''' || colspan=3 | Verify at Zero | ||
|- | |- | ||
| − | | '''Flight Mode Switch | + | | '''Flight Mode Switch: CH5 (Gear)''' || colspan=3 | Assign the CH5/Gear channel to a 3 Position switch |
|- | |- | ||
| − | | '''Flap Switch | + | | '''Flap Switch: CH6 (Aux1)''' || colspan=3 | Assign the CH6/Aux1 channel to a 3 Position switch<br>Do NOT use Transmitter Flap System. Flap Values are pre-programmed into the Aura. |
|- | |- | ||
| − | | '''Gyro Gain Kill Switch | + | | '''Gyro Gain Kill Switch: CH7/Aux2**'''|| colspan=3 | Assign the CH7/Aux2 channel to a 2 Position switch (Optional) |
|- | |- | ||
| − | | '''Crow Switch | + | | '''Crow Switch: CH8/Aux3**''' || colspan=3 | Assign the CH8/Aux3 channel to a 2 Position switch to a 2 Position Switch (Optional) |
|- | |- | ||
| '''First Flight Timer'''|| colspan=3 | For your first flight, set to 5:30 | | '''First Flight Timer'''|| colspan=3 | For your first flight, set to 5:30 | ||
Revision as of 22:13, 30 June 2023
Contents
Transmitter Model Setup Procedure
- Create a Blank Transmitter Airplane Model with 1 Throttle, 1 Aileron, 1 Elevator, 1 Rudder and any Flaps or Flap System OFF.
- Assign the Transmitter's Ch5/Gear channel to a 3 Position switch to change the Flight Modes in flight
- Assign the Transmitter's CH6/Aux1 Channel to a 3 Position switch to control the Flaps in flight
- (Optional) Assign the Transmitter's Ch7/Aux2 Channel to a 2 Position switch to function as a Gyro Gain Kill switch in flight
- The Gyro Gain Kill functionality is initially Disabled by default, but can be Enabled using Quick Set with your Transmitter
- (Optional) Assign the Transmitter's Ch8/Aux3 Channel to a 2 Position switch to function as a Crow switch in flight
- The Crow functionality is intially Disabled by default, but can be Enabled using Quick Set with your Transmitter
- Adjust Aileron, Elevator, Rudder and Throttle End Points (aka Travel Limits or ATV) as shown in the table below for your Transmitter brand
- Verify the rest of the settings as shown in the table below for your Transmitter brand
| Spektrum, Futaba, JR & Graupner | FrSky | Jeti (EX-Bus) | |
|---|---|---|---|
| Wing/Tail Type | 1 Aileron, 1 Elevator, 1 Rudder | 1 Aileron, 1 Elevator, 1 Rudder | 1 Aileron, 1 Elevator, 1 Rudder |
| End Points (Travel Adjust or ATV) | Ail/Ele/Rud: 125% | Ail/Ele/Rud: 100% | Ail/Ele/Rud: 100% |
| Throttle End Points (Travel Adjust or ATV) | Thr: 100% | Thr: 84% | Thr: 80% |
| Reversing | Not Allowed | ||
| Sub-Trim | Verify at Zero, NOT ALLOWED | ||
| Trim Levers | Verify at Zero | ||
| Flight Mode Switch: CH5 (Gear) | Assign the CH5/Gear channel to a 3 Position switch | ||
| Flap Switch: CH6 (Aux1) | Assign the CH6/Aux1 channel to a 3 Position switch Do NOT use Transmitter Flap System. Flap Values are pre-programmed into the Aura. | ||
| Gyro Gain Kill Switch: CH7/Aux2** | Assign the CH7/Aux2 channel to a 2 Position switch (Optional) | ||
| Crow Switch: CH8/Aux3** | Assign the CH8/Aux3 channel to a 2 Position switch to a 2 Position Switch (Optional) | ||
| First Flight Timer | For your first flight, set to 5:30 | ||
** - The Gyro Gain Kill Switch and Crow options are initially Disabled and can be Enabled using Quick Set from your Transmitter as detailed below
RV-8 60E G2 Options
- How to use Enable Crow with QuickSet from your Transmitter
- How to use Enable Gyro Gain Kill Switch with QuickSet from your Transmitter
