Difference between revisions of "RV-8 70cc/TransmitterSetup"
From Flex Innovations Wiki
(Created page with "{{DISPLAYTITLE:How to Setup your Transmitter for the RV-8 70cc with Aura}} __FORCETOC__ <!-- This forces the Table of Contents since it has less than 3 levels --> == Transmitt...") |
m |
||
Line 2: | Line 2: | ||
__FORCETOC__ <!-- This forces the Table of Contents since it has less than 3 levels --> | __FORCETOC__ <!-- This forces the Table of Contents since it has less than 3 levels --> | ||
== Transmitter Model Setup Procedure == | == Transmitter Model Setup Procedure == | ||
− | # Create a Blank Transmitter Airplane Model with 1 Throttle, 1 Aileron, 1 Elevator, 1 Rudder | + | # Create a Blank Transmitter Airplane Model with 1 Throttle, 1 Aileron, 1 Elevator, 1 Rudder |
+ | #* ''All Flaps and Flap Systems must be turned OFF. Flap values, Flap to Elevator mixes, and Flap Speed are preprogrammed in the Aura.'' | ||
# Assign the Transmitter's Ch5/Gear channel to a 3 Position switch to change the Flight Modes in flight | # Assign the Transmitter's Ch5/Gear channel to a 3 Position switch to change the Flight Modes in flight | ||
# Assign the Transmitter's CH6/Aux1 Channel to a 3 Position switch to control the Flaps in flight | # Assign the Transmitter's CH6/Aux1 Channel to a 3 Position switch to control the Flaps in flight | ||
Line 27: | Line 28: | ||
| '''Flight Mode Switch: CH5/Gear''' || colspan=3 | Assign the CH5/Gear channel to a 3 Position switch | | '''Flight Mode Switch: CH5/Gear''' || colspan=3 | Assign the CH5/Gear channel to a 3 Position switch | ||
|- | |- | ||
− | | '''Flap Switch: CH6/Aux1''' || colspan=3 | Assign the CH6/Aux1 channel to a 3 Position switch<br>Do NOT use Transmitter Flap System. | + | | '''Flap Switch: CH6/Aux1''' || colspan=3 | Assign the CH6/Aux1 channel to a 3 Position switch<br>Do NOT use Transmitter Flap System.<br>Flap Values, Flap to Elevator Mixes, and Flap Speed are pre-programmed into the Aura. |
|- | |- | ||
| '''Gyro Gain Kill Switch: CH7/Aux2**'''|| colspan=3 | Assign the CH7/Aux2 channel to a 2 Position switch (Optional) | | '''Gyro Gain Kill Switch: CH7/Aux2**'''|| colspan=3 | Assign the CH7/Aux2 channel to a 2 Position switch (Optional) |
Latest revision as of 19:46, 2 July 2023
Contents
Transmitter Model Setup Procedure
- Create a Blank Transmitter Airplane Model with 1 Throttle, 1 Aileron, 1 Elevator, 1 Rudder
- All Flaps and Flap Systems must be turned OFF. Flap values, Flap to Elevator mixes, and Flap Speed are preprogrammed in the Aura.
- Assign the Transmitter's Ch5/Gear channel to a 3 Position switch to change the Flight Modes in flight
- Assign the Transmitter's CH6/Aux1 Channel to a 3 Position switch to control the Flaps in flight
- Assign the Transmitter's Ch7/Aux2 Channel to a 2 Position switch to function as a Gyro Gain Kill switch in flight
- The Gyro Gain Kill functionality is Enabled by default when creating the Aura Config File, but can be Disabled.
- Adjust Aileron, Elevator, Rudder and Throttle End Points (aka Travel Limits or ATV) as shown in the table below for your Transmitter brand
- Verify the rest of the settings as shown in the table below for your Transmitter brand
Spektrum, Futaba, JR & Graupner | FrSky | Jeti (EX-Bus) | |
---|---|---|---|
Wing/Tail Type | 1 Aileron, 1 Elevator, 1 Rudder | 1 Aileron, 1 Elevator, 1 Rudder | 1 Aileron, 1 Elevator, 1 Rudder |
End Points (Travel Adjust or ATV) | Ail/Ele/Rud: 125% | Ail/Ele/Rud: 100% | Ail/Ele/Rud: 100% |
Reversing | Not Allowed | ||
Sub-Trim | Verify at Zero, NOT ALLOWED | ||
Trim Levers | Verify at Zero | ||
Flight Mode Switch: CH5/Gear | Assign the CH5/Gear channel to a 3 Position switch | ||
Flap Switch: CH6/Aux1 | Assign the CH6/Aux1 channel to a 3 Position switch Do NOT use Transmitter Flap System. Flap Values, Flap to Elevator Mixes, and Flap Speed are pre-programmed into the Aura. | ||
Gyro Gain Kill Switch: CH7/Aux2** | Assign the CH7/Aux2 channel to a 2 Position switch (Optional) |
** - The Gyro Gain Kill Switch is initially Enabled in the Aura Config Tool Wizard but can be Disabled.