Difference between revisions of "Mamba10/ServoAddendum"
| Line 17: | Line 17: | ||
**[http://www.resources.flexinnovations.com/files/Mamba10_Expert_Crow_DS15V2.acf '''Right-Click and Save As the new Aura Config File'''] to a folder on your PC. | **[http://www.resources.flexinnovations.com/files/Mamba10_Expert_Crow_DS15V2.acf '''Right-Click and Save As the new Aura Config File'''] to a folder on your PC. | ||
| − | + | '''How to configure the new Aura Config file onto your Mamba 10 Aura 8''' | |
| − | + | #Connect your Mamba's Aura to the Aura Config Tool. '''Read''' the settings from Aura and '''File->Save''' them to a folder on your PC for backup. | |
| − | + | #'''File-->Open''' the new Aura Config File you just downloaded in the Aura Config Tool. | |
| + | #On the '''Settings''' Tab, set your '''Transmitter Type''' and '''Receiver Connection''' fields. | ||
| + | #With the Aura still Connected '''Write All''' to Aura. | ||
'''NOTE:''' If you have manually set Aura '''Subtrims''', or have previously done a '''QUICK TRIM''', You can '''Open''' your back-up of your old settings and go through the '''Servo Ports''' (S1-S8) and make a NOTE of the '''Subtrim''' value in each port. You can then '''Read''' your new settings from Aura and enter these values in the '''Servo Ports->Subtrim''' and '''Write''' them to Aura. (Make sure you set '''View->Advanced View''') | '''NOTE:''' If you have manually set Aura '''Subtrims''', or have previously done a '''QUICK TRIM''', You can '''Open''' your back-up of your old settings and go through the '''Servo Ports''' (S1-S8) and make a NOTE of the '''Subtrim''' value in each port. You can then '''Read''' your new settings from Aura and enter these values in the '''Servo Ports->Subtrim''' and '''Write''' them to Aura. (Make sure you set '''View->Advanced View''') | ||
Revision as of 20:19, 30 July 2019
We made improvements to the DS-15 Servo used in the Mamba 10, but the roll-out of the servo was not properly controlled at the assembly line. Because of this, a small quantity of Mamba 10's with improved servos were shipped without the matching updates to the Aura Settings.
NOTE: If replacing servos with newly ordered (DS-15 V2) ones after early July 2019, you will need to load the new configuration file.
If your Mamba 10 feels like the gains are too high (typically indicated by in-flight oscillation or excessive "bouncing" after hard stops), then install our newest Aura configuration for the Mamba 10.
- Connect your Mamba's Aura to the Aura Config Tool. Read the settings from Aura and File->Save them to a folder on your PC for backup.
- New, Stock Aura Profile
- Right-Click and Save As the new Aura Config File to a folder on your PC.
- New, Stock - Crow Aura Profile
- Right-Click and Save As the new Aura Config File to a folder on your PC.
- New, Expert Aura Profile
- Right-Click and Save As the new Aura Config File to a folder on your PC.
- New, Expert - Crow Aura Profile
- Right-Click and Save As the new Aura Config File to a folder on your PC.
How to configure the new Aura Config file onto your Mamba 10 Aura 8
- Connect your Mamba's Aura to the Aura Config Tool. Read the settings from Aura and File->Save them to a folder on your PC for backup.
- File-->Open the new Aura Config File you just downloaded in the Aura Config Tool.
- On the Settings Tab, set your Transmitter Type and Receiver Connection fields.
- With the Aura still Connected Write All to Aura.
NOTE: If you have manually set Aura Subtrims, or have previously done a QUICK TRIM, You can Open your back-up of your old settings and go through the Servo Ports (S1-S8) and make a NOTE of the Subtrim value in each port. You can then Read your new settings from Aura and enter these values in the Servo Ports->Subtrim and Write them to Aura. (Make sure you set View->Advanced View)
