Difference between revisions of "Aura/JetiUse"
| Line 9: | Line 9: | ||
| − | We strongly recommend starting fresh with our | + | We '''strongly recommend''' starting fresh with our transmitter file that provides a pre-configured setup of the channel data in the order, amount, and direction, etc Aura E\expects. These are the general purpose transmitter files for typical models (If the UDI settings do not come in automatically, you can set them per the references in the PDF file just above): |
*[http://resources.flexinnovations.com/files/Wiki_Tx_Files/0021Aur2.jsn Click here to download and Jeti Transmitter (.jsn) file for a Mode 2 Transmitter (throttle on left)] | *[http://resources.flexinnovations.com/files/Wiki_Tx_Files/0021Aur2.jsn Click here to download and Jeti Transmitter (.jsn) file for a Mode 2 Transmitter (throttle on left)] | ||
*[http://resources.flexinnovations.com/files/Wiki_Tx_Files/0020Aur1.jsn Click here to download and Jeti Transmitter (.jsn) file for a Mode 1 Transmitter (throttle on right)] | *[http://resources.flexinnovations.com/files/Wiki_Tx_Files/0020Aur1.jsn Click here to download and Jeti Transmitter (.jsn) file for a Mode 1 Transmitter (throttle on right)] | ||
| Line 26: | Line 26: | ||
*[http://www.espritmodel.com/jeti-firmware-updates.aspx Jeti Firmware Page] | *[http://www.espritmodel.com/jeti-firmware-updates.aspx Jeti Firmware Page] | ||
| − | *[http://file.espritmodel.com/firmware/DEVUP2_Rx_324_UDI12%20Standard.zip Use | + | *[http://file.espritmodel.com/firmware/DEVUP2_Rx_324_UDI12%20Standard.zip Use this '''Standard''' Firmware Version for 12 channels in to Aura via UDI] |
'''Standard R3/RSW-18US 3.24''' (June, 2015) | '''Standard R3/RSW-18US 3.24''' (June, 2015) | ||
| Line 32: | Line 32: | ||
NOTE: The S.bus 3.24 firmware has not been tested and is not supported by Flex Innovations. | NOTE: The S.bus 3.24 firmware has not been tested and is not supported by Flex Innovations. | ||
| − | Check/Update your Jeti | + | Check/Update your Jeti receiver firmware before continuing! Firmware 3.24 '''standard''' or higher is considered '''MANDATORY''' by Flex Innovations. |
Revision as of 18:58, 18 August 2016
-Draft-
Instructions for Using Jeti Duplex Systems with Aura AFCS
Feedback requested. Please send E-mail to Aura Support
This document will provide the instructions and reference materials:
We strongly recommend starting fresh with our transmitter file that provides a pre-configured setup of the channel data in the order, amount, and direction, etc Aura E\expects. These are the general purpose transmitter files for typical models (If the UDI settings do not come in automatically, you can set them per the references in the PDF file just above):
- Click here to download and Jeti Transmitter (.jsn) file for a Mode 2 Transmitter (throttle on left)
- Click here to download and Jeti Transmitter (.jsn) file for a Mode 1 Transmitter (throttle on right)
It is recommended that you use the New Aura Config File (Wizard) and create a model file specifically for your model. We do provide these files for Test/Reference however.
- Click here to download an Aura Config File for a typical sport/scale model
- Click here to download an Aura Config File for a typical 3D model
Some helpful links for Jeti Information and Firmware
Standard R3/RSW-18US 3.24 (June, 2015)
NOTE: The special UDI 16 3.24 firmware has a different Header ID byte and is not supported at this time. NOTE: The S.bus 3.24 firmware has not been tested and is not supported by Flex Innovations.
Check/Update your Jeti receiver firmware before continuing! Firmware 3.24 standard or higher is considered MANDATORY by Flex Innovations.
