Difference between revisions of "Cypher/GraupnerInput"
From Flex Innovations Wiki
(→Reversing) |
(→Setup for using a Graupner HOTT Tx/Rx) |
||
(51 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
== '''Setup for using a Graupner HOTT Tx/Rx''' == | == '''Setup for using a Graupner HOTT Tx/Rx''' == | ||
− | <br /> | + | [[File:Rx_Connection_SBUS.png|thumb|upright=0.42|right|SUMD Connects like SBUS]] |
+ | <br /><br /> | ||
'''<big>Always start with a reset/new transmitter model!</big>''' | '''<big>Always start with a reset/new transmitter model!</big>''' | ||
<br /> | <br /> | ||
− | NOTE: You will use the 3-Pin to 4-Pin Male to Male cable provided to connect the Graupner Rx to the FLEXF3. This is the same cable arrangement shown on page 15 of the manual for the Futaba connections. (Non-Telemetry) | + | :'''NOTE:''' You will use the 3-Pin to 4-Pin Male to Male cable provided to connect the Graupner Rx to the FLEXF3. This is the same cable arrangement shown on page 15 of the manual for the Futaba connections. (Non-Telemetry) |
+ | :These instructions supplement the printed manual. Please read the manual before proceeding. | ||
+ | <br /> | ||
+ | We did ALSO test the newer tiny GR-12L S1051 SUMD + T Diversity to supply Control Data to the FLEXF3. It can supply Data via SUMD. | ||
+ | [[File:GR-12L SUMD S1051.jpg|thumb|upright=0.42|right|Note SUMD Output]] | ||
+ | *The instructions are very limited! [https://www.graupner.de/media/pdf/ab/f6/f2/S1045_S1046_S1051_SUMD_Diversity_Receiver_DE_V1sh_.pdf '''GR-12L S1051 Manual'''] | ||
+ | *The male cable is the SUMD out as indicted in the photo at right. | ||
+ | *Bind and configure the CH6/Male output to be SUMD (is SUMD of 16 on FW2.04) | ||
+ | *Since the male is the output unlike nearly all other receivers which have female outputs, you will need to fabricate an adapter to make the 4th Pin (Signal) connect like in the image above (Connect SUMD like S.BUS). (Require a 3pin Female to 4 pin Male cable) | ||
+ | *Telemetry has not been tested | ||
<br /><br /> | <br /><br /> | ||
---- | ---- | ||
=== CYPHER/Betaflight Settings === | === CYPHER/Betaflight Settings === | ||
− | Use one of the Betaflight configuration tools to make these settings. Be sure to '''SAVE''' the configuration page after adjustments.<br /> | + | :Use one of the Betaflight configuration tools to make these settings. Be sure to '''SAVE''' the configuration page after adjustments.<br /> |
+ | :We have not tested Graupner Telemetry at this time. If you have information, you can send it to support@flexinnovations.com and we can update our content. | ||
==== Configuration Page ==== | ==== Configuration Page ==== | ||
− | [[File: | + | [[File:Graupner_SUMD.png|thumb|upright=0.42|right|Betaflight Serial Provider Setting]][[File:Graupner_MAP_Order.png|thumb|upright=0.42|right|Betaflight Channel Map Setting]] |
+ | :Out of the box, only the 'Serial Receiver Provider' should need a change. | ||
<pre> | <pre> | ||
Receiver Mode -> Serial Based Receiver (Cypher Default) | Receiver Mode -> Serial Based Receiver (Cypher Default) | ||
Line 15: | Line 27: | ||
Telemetry slider -> OFF (Cypher Default) | Telemetry slider -> OFF (Cypher Default) | ||
</pre> | </pre> | ||
− | SAVE the page! | + | :'''SAVE''' the page! |
− | ==== | + | ==== Receiver Page ==== |
+ | :Should be same as out of box, but you can check! | ||
<pre> | <pre> | ||
− | Channel Order -> TAER1234 | + | Channel Order -> TAER1234 (Cypher Default - Same order as Spektrum) |
− | + | ||
− | + | ||
− | + | ||
</pre> | </pre> | ||
− | + | :'''SAVE''' the page! | |
<br /><br /> | <br /><br /> | ||
---- | ---- | ||
=== Graupner Transmitter settings: === | === Graupner Transmitter settings: === | ||
− | MX16 Mode 2 transmitter | + | :MX16 Mode 2 transmitter and GR-16 receiver used for validations |
− | (Most common models expected to work the SAME) | + | :(Most common models expected to work the SAME) |
− | You can verify the completed settings using the tools using the BetaFlight Receiver page. | + | :Receiver with diversity and SUMD out capability recommended. |
− | + | :You can verify the completed settings using the tools using the BetaFlight Receiver page. | |
==== Setup ==== | ==== Setup ==== | ||
<pre> | <pre> | ||
− | Name: | + | Name: Cypher |
Model Type: Plane/Acro | Model Type: Plane/Acro | ||
Wing type: 1 Ail, 0 Flaps (default) | Wing type: 1 Ail, 0 Flaps (default) | ||
Line 41: | Line 51: | ||
Throttles: 1 (default) | Throttles: 1 (default) | ||
The rest are defaults (default) | The rest are defaults (default) | ||
− | Assign a 2-position switch to CH5 | + | Assign a 2-position switch to CH5 (Stability/Angle Mode) |
− | Assign a 3-position switch to CH6 | + | Assign a 3-position switch to CH6 (Configuration/Tilt) |
Bind your Transmitter and Receiver | Bind your Transmitter and Receiver | ||
− | Set your system to output SUMD | + | Set your system to output SUMD serial data |
+ | No Subtrim should be used | ||
</pre><br /> | </pre><br /> | ||
− | |||
==== Reversing ==== | ==== Reversing ==== | ||
<pre> | <pre> | ||
1 Throttle => | 1 Throttle => | ||
− | 2 Aileron <= | + | 2 Aileron <= † |
− | 3 Elevator => | + | 3 Elevator => † |
− | 4 Rudder <= | + | 4 Rudder <= † |
− | 5 Gear => | + | 5 Gear => -or as desired |
− | 6 Aux1 <= -or as desired | + | 6 Aux1 <= ‡ -or as desired |
</pre> | </pre> | ||
+ | :'''NOTE:''' † Check 'reversing' by rotating the virtual 'body' on the Receiver Page of the Configurator | ||
+ | :'''NOTE:''' ‡ The internal Flex pilots set the CH6 switch UP/Back for forward flight and Low/Front for Hover. You can set per your preference. | ||
<br /> | <br /> | ||
==== Travel ==== | ==== Travel ==== | ||
+ | [[File:BF_RX_Notes.png|thumb|upright=0.42|right|Betaflight Travel Tune Notes]] | ||
<pre> | <pre> | ||
1 Throttle +-125% | 1 Throttle +-125% | ||
Line 65: | Line 78: | ||
4 Rudder +-125% | 4 Rudder +-125% | ||
5 Profile-Stab +-125% | 5 Profile-Stab +-125% | ||
− | 6 Config-Tilt +100 -60% To Start- | + | 6 Config-Tilt +100 -60% To Start - MUST adjust with gauges! |
</pre> | </pre> | ||
− | Go to the Receiver Page in Configurator and fine tune Aileron,Elevator, and Rudder travel to 1000-1500-2000. (See notes on top of Configurator page) | + | :'''NOTE:''' Go to the Receiver Page in Configurator and fine tune Aileron,Elevator, and Rudder travel to 1000-1500-2000. (See notes on top of Configurator page) |
− | <br /> | + | <br /> |
− | + | ||
==== Timers ==== | ==== Timers ==== | ||
<pre> | <pre> | ||
Line 75: | Line 87: | ||
Timer length suggestion for first flights | Timer length suggestion for first flights | ||
2200mAh: 2:30 | 2200mAh: 2:30 | ||
− | 2600mAh: 3: | + | 2600mAh: 3:00 |
− | 3300mAh: | + | 3300mAh: 3:40 |
− | </pre><br /> | + | </pre> |
+ | <br /> | ||
+ | [[Cypher|Cypher Wiki Main]] |
Latest revision as of 18:30, 19 March 2020
Contents
Setup for using a Graupner HOTT Tx/Rx
Always start with a reset/new transmitter model!
- NOTE: You will use the 3-Pin to 4-Pin Male to Male cable provided to connect the Graupner Rx to the FLEXF3. This is the same cable arrangement shown on page 15 of the manual for the Futaba connections. (Non-Telemetry)
- These instructions supplement the printed manual. Please read the manual before proceeding.
We did ALSO test the newer tiny GR-12L S1051 SUMD + T Diversity to supply Control Data to the FLEXF3. It can supply Data via SUMD.
- The instructions are very limited! GR-12L S1051 Manual
- The male cable is the SUMD out as indicted in the photo at right.
- Bind and configure the CH6/Male output to be SUMD (is SUMD of 16 on FW2.04)
- Since the male is the output unlike nearly all other receivers which have female outputs, you will need to fabricate an adapter to make the 4th Pin (Signal) connect like in the image above (Connect SUMD like S.BUS). (Require a 3pin Female to 4 pin Male cable)
- Telemetry has not been tested
CYPHER/Betaflight Settings
- Use one of the Betaflight configuration tools to make these settings. Be sure to SAVE the configuration page after adjustments.
- We have not tested Graupner Telemetry at this time. If you have information, you can send it to support@flexinnovations.com and we can update our content.
Configuration Page
- Out of the box, only the 'Serial Receiver Provider' should need a change.
Receiver Mode -> Serial Based Receiver (Cypher Default) Serial Receiver Provider -> SUMD (aka Graupner SUMD) Telemetry slider -> OFF (Cypher Default)
- SAVE the page!
Receiver Page
- Should be same as out of box, but you can check!
Channel Order -> TAER1234 (Cypher Default - Same order as Spektrum)
- SAVE the page!
Graupner Transmitter settings:
- MX16 Mode 2 transmitter and GR-16 receiver used for validations
- (Most common models expected to work the SAME)
- Receiver with diversity and SUMD out capability recommended.
- You can verify the completed settings using the tools using the BetaFlight Receiver page.
Setup
Name: Cypher Model Type: Plane/Acro Wing type: 1 Ail, 0 Flaps (default) Tail type: Normal 1 Elev 1 Rudd (default) Throttles: 1 (default) The rest are defaults (default) Assign a 2-position switch to CH5 (Stability/Angle Mode) Assign a 3-position switch to CH6 (Configuration/Tilt) Bind your Transmitter and Receiver Set your system to output SUMD serial data No Subtrim should be used
Reversing
1 Throttle => 2 Aileron <= † 3 Elevator => † 4 Rudder <= † 5 Gear => -or as desired 6 Aux1 <= ‡ -or as desired
- NOTE: † Check 'reversing' by rotating the virtual 'body' on the Receiver Page of the Configurator
- NOTE: ‡ The internal Flex pilots set the CH6 switch UP/Back for forward flight and Low/Front for Hover. You can set per your preference.
Travel
1 Throttle +-125% 2 Aileron +-125% 3 Elevator +-125% 4 Rudder +-125% 5 Profile-Stab +-125% 6 Config-Tilt +100 -60% To Start - MUST adjust with gauges!
- NOTE: Go to the Receiver Page in Configurator and fine tune Aileron,Elevator, and Rudder travel to 1000-1500-2000. (See notes on top of Configurator page)
Timers
Set a count down Timer length suggestion for first flights 2200mAh: 2:30 2600mAh: 3:00 3300mAh: 3:40