Difference between revisions of "Cypher/JetiInput"

Revision as of 21:02, 9 August 2019

Setup for using a Jeti Tx/Rx

Always start with a reset/new transmitter model!

Cypher/Betaflight Settings

Configuration Page

*Receiver Mode            ->    Serial Based Receiver  (Cypher Default)
*Serial Receiver Provide  ->    JETIEXBUS
*Telemetry slider         ->    OFF                    (Cypher Default - Unless configuring with telemetry based on those supplementary instructions)

Receiver Page

*Channel Order            ->    TAER1234               (Cypher Default - Same as Spektrum)

Transmitter settings:

DS-16 transmitter and R3 EX RSW Receiver used for validations (Most common models expected to work the SAME)

Model->New Model

*Name:                  FV-31 Cypher
*Model Type:            Aero

Bind to Rx per Jeti instructions (verify function with servo in port 2 if desired)

Model->Basic Properties

*Name:                  FV-31 Cypher
*Wing type:             0 Flaps, 1 Ail
*Tail type:             Normal 1H1V        (default)
*Engine count:          1                  (default)
*The rest are defaults                     (default)

Model->Functions Assignment

*1   Ailerons          -control P1      -(default)
*2   Elevator          -control P2      -(default)
*3   Rudder            -control P3      -(default)
*4   Throttle          -control P4      -(default)
*5   Profile-Stabil    -Sb              -or 2 position switch of users choice for stability profile
*6   Config-Tilt       -Sa              -or 3 position switch of users choice for configuration / fan tilt
*7   Arming            -Sd              (totally optional -use this of other switch if arming switch will be configured later)
*8   Mode Rates        -Sc              (totally optional -use if multi-rates will be implemented in BF for example)
*9   R Slider           P5              (totally optional -not currently used but drives spare servo port on FLEXF3)
*10   L Slider          P6              (totally optional -not currently used but drives spare servo port on FLEXF3)

Note: do not hit the Auto assign button!

Model->Servo Assignment
Sets output order to same as Spektrum: Links the above functions to ‘output slots’ in data stream

*1    Throttle
*2    Aileron
*3    Elevator
*4    Rudder
*5    Profile-Stab      (Angle Mode / Stability 3 -vs- 6 axis)
*6    Config-Tilt       (Fan Tilt / Configuration switch)
*7    Arming            (Optional)
*8    Mode Rates        (Optional
*9    R Slider          (Optional)
*10   L Slider          (Optional)

Model->Servo Setup

All items set to defaults except as noted
ALL subtrims 0%                  (defaults)
Travels                          (General)
   All Max Positive are   100%   except for the Config/Tilt noted below     (defaults)
   All Max Negative are  -100%   except for the Config/Tilt noted below     (defaults)
Travel for Config/Tilt           (start with these and '''MUST''' adjust with gauges)
   Max Positive           81%  
   Max Negative          -57%
Reversing          (1-10 in Servo Assignment order as just above)
                   (Normal is “Reverse NO”, Reverse is “Reverse YES”)
   1  NO                  (normal)
   2  NO
   3  NO
   4  NO
   5  YES †               (reversed)
   6  NO  †
   7  NO  †
   8  NO  †
   9  NO  †
   10 NO  †
†User can set items 5-10 per their preference

Do the command and gyro checks

Model->Timers/Sensors

*Timers:    Set a free running
*Timer length suggestion for first flights
     2200mAh:            2:30
     2600mAh:            3:10
     3300mAh:            4:00
Other settings for telemetry/Alarms can be introduced in Wiki

Model->Device Explorer
(with system powered and bound)

Under Receiver (ex. R3 EX with ‘Check Mark’)
- Serial Link: EX Bus
- Note the JETIBOX/EX Bus Pin: “Value” for plugging in Male to Male Cable On the R3-EX it is “Ext” which is marked “4/EXT” on the receiver.
- Rest of settings are defaults/or as user desires

(Note: Output period shows 17ms)