Difference between revisions of "Cypher/JetiInput"

Revision as of 16:33, 10 August 2019

Setup for using a Jeti Tx/Rx

Betaflight Provider Setting

Always start with a reset/new transmitter model!
NOTE: You will use the 3-Pin to 4-Pin Male to Male cable provided to connect the Jeti Rx to the FLEXF3. This is the same cable arrangement shown on page 15 of the manual for the Futaba connections. (Non-Telemetry)

CYPHER/Betaflight Settings

Use one of the Betaflight configuration tools to make these settings. Be sure to SAVE the page after adjustments.

Configuration Page

Receiver Mode            ->  Serial Based Receiver (Cypher Default)
Serial Receiver Provider ->  JETIEXBUS
Telemetry slider         ->  OFF             (Cypher Default - Unless configuring with telemetry
                                             based using the other supplementary instructions)

Receiver Page

Channel Order             ->    TAER1234               (Cypher Default - Same order as Spektrum)

JETI Transmitter settings:

DS-16 Mode 2 transmitter and R3 EX RSW Receiver used for validations (Most common models expected to work the SAME)
You can verify the completed settings using the tools using the BetaFlight Receiver page.

Model->New Model

Name:                  FV-31 Cypher
Model Type:            Aero

Bind to Rx per Jeti instructions (verify function with servo in port 2 if desired)

Model->Basic Properties

Name:                  FV-31 Cypher
Wing type:             0 Flaps, 1 Ail
Tail type:             Normal 1H1V        (default)
Engine count:          1                  (default)
The rest are defaults                     (default)

Model->Functions Assignment

1    Ailerons         -control P1      -(default)
2    Elevator         -control P2      -(default)
3    Rudder           -control P3      -(default)
4    Throttle         -control P4      -(default)
5    Profile-Stabil   -Sb       -or 2 position switch of users choice for stability profile
6    Config-Tilt      -Sa       -or 3 position switch of users choice for configuration / fan tilt
7    Arming           -Sd       (totally optional -use this of other switch if arming switch will be configured later)
8    Mode Rates       -Sc       (totally optional -use if multi-rates will be implemented in BF for example)
9    R Slider          P5       (totally optional -not currently used but drives spare servo port on FLEXF3)
10   L Slider          P6       (totally optional -not currently used but drives spare servo port on FLEXF3)

NOTE: do not hit the Auto-Assign button!

Model->Servo Assignment
Sets output order to same as Spektrum: Links the above functions to ‘output slots’ in data stream

1    Throttle
2    Aileron
3    Elevator
4    Rudder
5    Profile-Stab      (Angle Mode / Stability 3 -vs- 6 axis)
6    Config-Tilt       (Fan Tilt / Configuration switch)
7    Arming            (Optional)
8    Mode Rates        (Optional
9    R Slider          (Optional)
10   L Slider          (Optional)

Model->Servo Setup

All items set to defaults except as noted
ALL subtrims 0%               (defaults)
Travels                       (General)
   All Max Positive  100%   except for the Config/Tilt noted below     (defaults)
   All Max Negative -100%   except for the Config/Tilt noted below     (defaults)
Travel for Config/Tilt        (start with these and then you MUST adjust final angle with gauges)
   Max Positive           81%  
   Max Negative          -57%
Reversing                     (1-10 in Servo Assignment order as just above)
   1  NO                      (Normal is “Reverse NO”, Reverse is “Reverse YES”)
   2  NO
   3  NO
   4  NO
   5  YES †     
   6  NO  †
   7  NO  †
   8  NO  †
   9  NO  †
   10 NO  †
†User can set items 5-10 per their preference

Do the command and gyro checks

Model->Timers/Sensors

Timers:    Set a free running
Timer length suggestion for first flights
     2200mAh:            2:30
     2600mAh:            3:10
     3300mAh:            4:00
Other settings for telemetry/Alarms can be introduced in Wiki

Model->Device Explorer

With system powered and bound
  Under Receiver             Example: R3 EX with ‘Check Mark’
     Serial Link:            EX Bus
     Note the JETIBOX/EX Bus Pin “Value” for plugging in Male to Male Cable.
     On the R3-EX it is “Ext” which is marked “4/EXT” on the receiver.
     The rest of settings are defaults/or as user desires
Note: Output period shows 17ms