Difference between revisions of "Cypher/JetiInput"

From Flex Innovations Wiki
Jump to: navigation, search
(→‎Cypher/Betaflight Settings)
(→‎JETI Transmitter settings:)
 
(100 intermediate revisions by the same user not shown)
Line 1: Line 1:
 
== '''Setup for using a Jeti Tx/Rx''' ==
 
== '''Setup for using a Jeti Tx/Rx''' ==
 +
<br />
 +
[[File:Rx_Connection_SBUS.png|thumb|upright=0.42|right|Normal EXBUS Connects like SBUS]]
 +
[[File:Jeti Rx Set.png|thumb|upright=0.42|right|Betaflight Provider Setting]]
 +
'''<big>Always start with a reset/new transmitter model!</big>'''
 +
<br />
 +
:'''NOTE:''' You will use the 3-Pin to 4-Pin Male to Male cable provided to connect the Jeti Rx to the FLEXF3. This is the same cable arrangement shown on page 15 of the manual for the Futaba connections. (Non-Telemetry)
 +
:These instructions supplement the printed manual. Please read the manual before proceeding.
 +
<br /><br />
 +
----
 +
=== CYPHER/Betaflight Settings ===
 +
Use one of the Betaflight configuration tools to make these settings. Be sure to '''SAVE''' the page after adjustments.<br />
 +
==== Configuration Page ====
  
−
'''Always start with a reset/new transmitter model!'''
+
<pre>
−
 
+
Receiver Mode           ->  Serial Based Receiver (Cypher Default)
−
=== Cypher/Betaflight Settings ===
+
Serial Receiver Provider ->  JETIEXBUS
−
'''''Configuration Page'''''
+
Telemetry slider         ->  OFF       (Cypher Default - Unless configuring with telemetry
−
*Receiver Mode ->  Serial Based Receiver (Cypher Default)
+
                                        based using the other supplementary instructions)
−
*Serial Receiver Provide ->  JETIEXBUS
+
</pre>
−
*Telemetry slider is OFF (Cypher Default - Unless configuring with telemetry based on those supplementary instructions)
+
:'''SAVE''' the Page
−
 
+
−
'''''Receiver Page'''''
+
−
*Channel Order  ->  TAER1234  (Cypher Default - Same as Spektrum)
+
 
<br />
 
<br />
  
 +
==== Receiver Page ====
 
<pre>
 
<pre>
−
Some text      aligned
+
Channel Order            ->  TAER1234  (Cypher Default - Same order as Spektrum)
−
Next          aligned
+
−
Test          yep          next
+
 
</pre>
 
</pre>
 +
:'''SAVE''' the Page
 
<br />
 
<br />
 +
----
  
−
=== Transmitter settings: ===
+
=== JETI Transmitter settings: ===
  
−
DS-16 transmitter and R3 EX RSW Receiver used for validations
+
:DS-16 Mode 2 transmitter and R3 EX RSW Receiver used for validations
−
(Most common models expected to work the SAME)
+
:(Most common models expected to work the SAME)<br />
 +
:As always, start with a freshly '''RESET''' transmitter model.
 +
:You can verify the completed settings using the tools using the BetaFlight Configurator Receiver page.
 
<br /><br />
 
<br /><br />
 
''<big>Model->New Model</big>''
 
''<big>Model->New Model</big>''
−
*Name: FV-31 Cypher
+
<pre>
−
*Model Type: Aero
+
Name:                 FV-31 Cypher
−
<br />
+
Model Type:           Aero
−
Bind to Rx per Jeti instructions (verify function with servo in port 2 if desired)
+
</pre>
 +
:Bind to Rx per Jeti instructions (verify function with servo in port 2 if desired)
 
<br /><br />
 
<br /><br />
 
''<big>Model->Basic Properties</big>''
 
''<big>Model->Basic Properties</big>''
−
<br />
+
<pre>
−
*Name: FV-31 Cypher
+
Name:                 FV-31 Cypher
−
*Wing type: 0 Flaps, 1 Ail
+
Wing type:             0 Flaps, 1 Ail
−
*Tail type: Normal 1H1V (default)
+
Tail type:             Normal 1H1V       (default)
−
*Engine count: 1 (default)
+
Engine count:         1                 (default)
−
*The rest are defaults (default)
+
The rest are defaults                     (default)
−
<br />
+
</pre><br />
 +
 
 
''<big>Model->Functions Assignment</big>''
 
''<big>Model->Functions Assignment</big>''
 +
<pre>
 +
1  Ailerons      -control P1      -(default)
 +
2  Elevator      -control P2      -(default)
 +
3  Rudder        -control P3      -(default)
 +
4  Throttle      -control P4      -(default)
 +
5  Profile-Stabil -Sb  -or 2 position switch of users choice-stability profile
 +
6  Config-Tilt    -Sa  -or 3 position switch of users choice-configuration/fan tilt
 +
7  Arming        -Sd  -optional-use this or other sw if arming switch will be configured)
 +
8  Mode Rates    -Sc  -optional-use if multi-rates will be implemented in BF for example)
 +
9  R Slider      -P5  -optional-not currently used-drives spare servo port on FLEXF3)
 +
10  L Slider      -P6  -optional-not currently used-drives spare servo port on FLEXF3)
 +
</pre><big>'''NOTE:''' '''''do NOT''''' hit the Auto-Assign button!</big>
 
<br />
 
<br />
−
*1 Ailerons    -control P1                  -(default)
 
−
*2 Elevator    -control P2                  -(default)
 
−
*3 Rudder      -control P3                  -(default)
 
−
*4 Throttle    -control P4                  -(default)
 
−
*5 Profile-Stabil    -Sb -or 2 position switch of users choice for stability profile
 
−
*6 Config-Tilt      -Sa -or 3 position switch of users choice for configuration / fan tilt
 
−
*7 Arming            -Sd            (totally optional -use this of other switch if arming switch will be configured later)
 
−
*8 Mode Rates        -Sc            (totally optional -use if multi-rates will be implemented in BF for example)
 
−
*9 R Slider          P5            (totally optional -not currently used but drives spare servo port on FLEXF3)
 
−
*10 L Slider          P6            (totally optional -not currently used but drives spare servo port on FLEXF3)
 
−
<big>'''Note:''' do not hit the Auto assign button!</big>
 
−
<br /><br />
 
 
''<big>Model->Servo Assignment</big>''
 
''<big>Model->Servo Assignment</big>''
 
<br />
 
<br />
−
(sets output order… to same as Spektrum: Links the above functions to ‘output slots’ in data stream)
+
:Sets output order to same as Spektrum: Links the above functions to ‘output slots’ in data stream
−
*1    Throttle
+
<pre>
−
*2    Aileron
+
1    Throttle
−
*3    Elevator
+
2    Aileron
−
*4    Rudder
+
3    Elevator
−
*5    Profile-Stab   (Angle Mode / Stability 3 -vs- 6 axis)
+
4    Rudder
−
*6    Config-Tilt     (Fan Tilt / Configuration switch)
+
5    Profile-Stab     (Angle Mode / Stability 3 -vs- 6 axis)
−
*7    Arming         (Optional)
+
6    Config-Tilt       (Fan Tilt / Configuration switch)
−
*8    Mode Rates     (Optional
+
7    Arming           (Optional)
−
*9    R Slider       (Optional)
+
8    Mode Rates       (Optional
−
*10  L Slider       (Optional)
+
9    R Slider         (Optional)
−
<br />
+
10  L Slider         (Optional)
 +
</pre><br />
 
''<big>Model->Servo Setup</big>''
 
''<big>Model->Servo Setup</big>''
−
<br />
+
[[File:BF_RX_Notes.png|thumb|upright=0.42|right|Betaflight Travel Tune Notes]]
−
*All items set to defaults except as noted
+
<pre>
−
*ALL subtrims 0% (defaults)
+
All items set to defaults except as noted
−
*Travels
+
ALL subtrims 0%             (defaults)
−
**All Max Positive are 100% except for the Config/Tilt noted below (defaults) (Travels)
+
−
**All Max Negative are -100% except for the Config/Tilt noted below (defaults) (Travels)
+
−
**Config/Tilt Travel (start here and MUST adjust with gauges)<br />
+
−
***Max Positive      81%    (travel)
+
−
***Max Negative      -57%
+
−
*Reversing (1-10 in Servo Assignment order as just above) (Normal is “Reverse NO”, Reverse is “Reverse YES”)
+
−
**1 NO  (normal)
+
−
**2 NO
+
−
**3 NO
+
−
**4 NO
+
−
**5 YES † (reversed)
+
−
**6 NO †
+
−
**7 NO †
+
−
**8 NO †
+
−
**9 NO †
+
−
**10 NO †
+
  
−
†User can change per preference<br />
+
Travels                    -general
−
(Do the command and gyro checks)<br />
+
  All Max Positive  100%  -except for the Config/Tilt noted below    (defaults)
−
<br />
+
  All Max Negative -100%  -except for the Config/Tilt noted below    (defaults)
 +
Travel for Config/Tilt     
 +
  Max Positive      81%    -start with these and then you MUST adjust final angle w/gauges
 +
  Max Negative    -57%
 +
 
 +
Reversing                    1-10 in Servo Assignment order as just above
 +
  1  NO  ‡                  Normal is “Reverse NO”, Reverse is “Reverse YES”
 +
  2  NO  ‡
 +
  3  NO  ‡
 +
  4  NO  ‡
 +
  5  YES †    Or as user prefers for Stability/ANGLE MODE
 +
  6  NO  §    Or as user prefers for Configuration/Fan Tilt
 +
  7  NO  †
 +
  8  NO  †
 +
  9  NO  †
 +
  10 NO  †
 +
</pre>
 +
:'''NOTE:'''† User can set items 5-10 per their preference
 +
:'''NOTE:'''‡ You must check Aileron, Elevator, Rudder 'Reversing' by rotating the virtual 'body' on the Receiver Page of the Configurator
 +
:'''NOTE:'''§ The internal Flex pilots set the CH6 switch UP/Back for forward flight and Low/Front for Hover. You can set per your preference.
 +
:'''Do the command and gyro checks in the manual'''
 +
<br /><br />
 
''<big>Model->Timers/Sensors</big>''
 
''<big>Model->Timers/Sensors</big>''
−
*Timers: Set a free running
+
<pre>
−
*Time suggestion for first flights
+
Timers:   Set a free running
−
**2200mAh:            2:30
+
Timer length suggestion for first flights
−
**2600mAh:           3:10
+
    2200mAh:            2:30
−
**3300mAh:            4:00
+
    2600mAh:           3:00
 +
    3300mAh:            3:40
 
Other settings for telemetry/Alarms can be introduced in Wiki
 
Other settings for telemetry/Alarms can be introduced in Wiki
−
<br /><br />
+
</pre><br />
 
''<big>Model->Device Explorer</big>''
 
''<big>Model->Device Explorer</big>''
−
<br />
+
<pre>
−
(with system powered and bound)
+
With system powered and bound
−
<br />
+
  Under Receiver             Example: R3 EX with ‘Check Mark’
−
*Under Receiver (ex. R3 EX with ‘Check Mark’)
+
    Serial Link:           EX Bus
−
**Serial Link: EX Bus
+
    Note the JETIBOX/EX Bus Pin “Value” for plugging in Male to Male Cable.
−
**Note the JETIBOX/EX Bus Pin: “Value” for plugging in Male to Male Cable On the R3-EX it is “Ext” which is marked “4/EXT” on the receiver.
+
    On the R3-EX it is “Ext” which is marked “4/EXT” on the receiver.
−
**Rest of settings are defaults/or as user desires<br />
+
    The rest of settings are defaults/or as user desires
−
(Note: Output period shows 17ms)
+
Note: Output period shows 17ms
−
<br /><br />
+
</pre><br />
  
 
===Some third party links on using Jeti with Betaflight: ===
 
===Some third party links on using Jeti with Betaflight: ===
Line 122: Line 143:
  
 
https://www.rcgroups.com/forums/showpost.php?p=33054194&postcount=8
 
https://www.rcgroups.com/forums/showpost.php?p=33054194&postcount=8
 +
<br /><br />
 +
[[Cypher|Cypher Wiki Main]]

Latest revision as of 16:36, 10 September 2019

Setup for using a Jeti Tx/Rx


Normal EXBUS Connects like SBUS
Betaflight Provider Setting

Always start with a reset/new transmitter model!

NOTE: You will use the 3-Pin to 4-Pin Male to Male cable provided to connect the Jeti Rx to the FLEXF3. This is the same cable arrangement shown on page 15 of the manual for the Futaba connections. (Non-Telemetry)
These instructions supplement the printed manual. Please read the manual before proceeding.



CYPHER/Betaflight Settings

Use one of the Betaflight configuration tools to make these settings. Be sure to SAVE the page after adjustments.

Configuration Page

Receiver Mode            ->  Serial Based Receiver (Cypher Default)
Serial Receiver Provider ->  JETIEXBUS
Telemetry slider         ->  OFF        (Cypher Default - Unless configuring with telemetry
                                         based using the other supplementary instructions)
SAVE the Page


Receiver Page

Channel Order            ->  TAER1234   (Cypher Default - Same order as Spektrum)
SAVE the Page


JETI Transmitter settings:

DS-16 Mode 2 transmitter and R3 EX RSW Receiver used for validations
(Most common models expected to work the SAME)
As always, start with a freshly RESET transmitter model.
You can verify the completed settings using the tools using the BetaFlight Configurator Receiver page.



Model->New Model 

Name:                  FV-31 Cypher
Model Type:            Aero
Bind to Rx per Jeti instructions (verify function with servo in port 2 if desired)



Model->Basic Properties 

Name:                  FV-31 Cypher
Wing type:             0 Flaps, 1 Ail
Tail type:             Normal 1H1V        (default)
Engine count:          1                  (default)
The rest are defaults                     (default)

Model->Functions Assignment 

1   Ailerons       -control P1      -(default)
2   Elevator       -control P2      -(default)
3   Rudder         -control P3      -(default)
4   Throttle       -control P4      -(default)
5   Profile-Stabil -Sb   -or 2 position switch of users choice-stability profile
6   Config-Tilt    -Sa   -or 3 position switch of users choice-configuration/fan tilt
7   Arming         -Sd   -optional-use this or other sw if arming switch will be configured)
8   Mode Rates     -Sc   -optional-use if multi-rates will be implemented in BF for example)
9   R Slider       -P5   -optional-not currently used-drives spare servo port on FLEXF3)
10  L Slider       -P6   -optional-not currently used-drives spare servo port on FLEXF3)
NOTE: do NOT hit the Auto-Assign button!


Model->Servo Assignment

Sets output order to same as Spektrum: Links the above functions to ‘output slots’ in data stream
1    Throttle
2    Aileron
3    Elevator
4    Rudder
5    Profile-Stab      (Angle Mode / Stability 3 -vs- 6 axis)
6    Config-Tilt       (Fan Tilt / Configuration switch)
7    Arming            (Optional)
8    Mode Rates        (Optional
9    R Slider          (Optional)
10   L Slider          (Optional)

Model->Servo Setup

Betaflight Travel Tune Notes
All items set to defaults except as noted
ALL subtrims 0%             (defaults)

Travels                     -general
   All Max Positive  100%   -except for the Config/Tilt noted below     (defaults)
   All Max Negative -100%   -except for the Config/Tilt noted below     (defaults)
Travel for Config/Tilt      
   Max Positive      81%    -start with these and then you MUST adjust final angle w/gauges
   Max Negative     -57%

Reversing                    1-10 in Servo Assignment order as just above
   1  NO  ‡                  Normal is “Reverse NO”, Reverse is “Reverse YES”
   2  NO  ‡
   3  NO  ‡
   4  NO  ‡
   5  YES †    Or as user prefers for Stability/ANGLE MODE
   6  NO  §    Or as user prefers for Configuration/Fan Tilt
   7  NO  †
   8  NO  †
   9  NO  †
   10 NO  †
NOTE:† User can set items 5-10 per their preference
NOTE:‡ You must check Aileron, Elevator, Rudder 'Reversing' by rotating the virtual 'body' on the Receiver Page of the Configurator
NOTE:§ The internal Flex pilots set the CH6 switch UP/Back for forward flight and Low/Front for Hover. You can set per your preference.
Do the command and gyro checks in the manual



Model->Timers/Sensors 

Timers:    Set a free running
Timer length suggestion for first flights
     2200mAh:            2:30
     2600mAh:            3:00
     3300mAh:            3:40
Other settings for telemetry/Alarms can be introduced in Wiki

Model->Device Explorer 

With system powered and bound
  Under Receiver             Example: R3 EX with ‘Check Mark’
     Serial Link:            EX Bus
     Note the JETIBOX/EX Bus Pin “Value” for plugging in Male to Male Cable.
     On the R3-EX it is “Ext” which is marked “4/EXT” on the receiver.
     The rest of settings are defaults/or as user desires
Note: Output period shows 17ms

Some third party links on using Jeti with Betaflight:

https://github.com/betaflight/betaflight/issues/167

https://github.com/betaflight/betaflight/blob/master/docs/Telemetry.md

https://www.drone-zone.de/anleitung-jeti-ex-telemetrie-mit-betaflight/

https://www.rcgroups.com/forums/showthread.php?2530376-Multirotor-Controller-Setup

https://www.rcgroups.com/forums/showpost.php?p=33054194&postcount=8

Cypher Wiki Main

Retrieved from "https://wiki.flexinnovations.com/index.php?title=Cypher/JetiInput&oldid=3671"