Difference between revisions of "Cypher/JetiInput"
From Flex Innovations Wiki
(→CYPHER/Betaflight Settings) |
(→JETI Transmitter settings:) |
||
| (43 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
== '''Setup for using a Jeti Tx/Rx''' == | == '''Setup for using a Jeti Tx/Rx''' == | ||
<br /> | <br /> | ||
| + | [[File:Rx_Connection_SBUS.png|thumb|upright=0.42|right|Normal EXBUS Connects like SBUS]] | ||
[[File:Jeti Rx Set.png|thumb|upright=0.42|right|Betaflight Provider Setting]] | [[File:Jeti Rx Set.png|thumb|upright=0.42|right|Betaflight Provider Setting]] | ||
'''<big>Always start with a reset/new transmitter model!</big>''' | '''<big>Always start with a reset/new transmitter model!</big>''' | ||
<br /> | <br /> | ||
| − | NOTE: You will use the 3-Pin to 4-Pin Male to Male cable provided to connect the Jeti Rx to the FLEXF3. This is the same cable arrangement shown on page 15 of the manual for the Futaba connections. (Non-Telemetry) | + | :'''NOTE:''' You will use the 3-Pin to 4-Pin Male to Male cable provided to connect the Jeti Rx to the FLEXF3. This is the same cable arrangement shown on page 15 of the manual for the Futaba connections. (Non-Telemetry) |
| − | <br /> | + | :These instructions supplement the printed manual. Please read the manual before proceeding. |
| + | <br /><br /> | ||
| + | ---- | ||
=== CYPHER/Betaflight Settings === | === CYPHER/Betaflight Settings === | ||
| − | Use one of the Betaflight configuration tools to make these settings. Be sure to '''SAVE''' the page after adjustments. | + | Use one of the Betaflight configuration tools to make these settings. Be sure to '''SAVE''' the page after adjustments.<br /> |
| − | + | ==== Configuration Page ==== | |
| − | + | ||
<pre> | <pre> | ||
Receiver Mode -> Serial Based Receiver (Cypher Default) | Receiver Mode -> Serial Based Receiver (Cypher Default) | ||
| Line 16: | Line 19: | ||
based using the other supplementary instructions) | based using the other supplementary instructions) | ||
</pre> | </pre> | ||
| + | :'''SAVE''' the Page | ||
| + | <br /> | ||
| − | + | ==== Receiver Page ==== | |
<pre> | <pre> | ||
Channel Order -> TAER1234 (Cypher Default - Same order as Spektrum) | Channel Order -> TAER1234 (Cypher Default - Same order as Spektrum) | ||
</pre> | </pre> | ||
| + | :'''SAVE''' the Page | ||
<br /> | <br /> | ||
| + | ---- | ||
=== JETI Transmitter settings: === | === JETI Transmitter settings: === | ||
| − | DS-16 Mode 2 transmitter and R3 EX RSW Receiver used for validations | + | :DS-16 Mode 2 transmitter and R3 EX RSW Receiver used for validations |
| − | (Most common models expected to work the SAME)<br /> | + | :(Most common models expected to work the SAME)<br /> |
| − | You can verify the completed settings using the tools using the BetaFlight Receiver page. | + | :As always, start with a freshly '''RESET''' transmitter model. |
| + | :You can verify the completed settings using the tools using the BetaFlight Configurator Receiver page. | ||
<br /><br /> | <br /><br /> | ||
''<big>Model->New Model</big>'' | ''<big>Model->New Model</big>'' | ||
| Line 34: | Line 42: | ||
Model Type: Aero | Model Type: Aero | ||
</pre> | </pre> | ||
| − | Bind to Rx per Jeti instructions (verify function with servo in port 2 if desired) | + | :Bind to Rx per Jeti instructions (verify function with servo in port 2 if desired) |
<br /><br /> | <br /><br /> | ||
''<big>Model->Basic Properties</big>'' | ''<big>Model->Basic Properties</big>'' | ||
| Line 47: | Line 55: | ||
''<big>Model->Functions Assignment</big>'' | ''<big>Model->Functions Assignment</big>'' | ||
<pre> | <pre> | ||
| − | 1 | + | 1 Ailerons -control P1 -(default) |
| − | 2 | + | 2 Elevator -control P2 -(default) |
| − | 3 | + | 3 Rudder -control P3 -(default) |
| − | 4 | + | 4 Throttle -control P4 -(default) |
| − | 5 | + | 5 Profile-Stabil -Sb -or 2 position switch of users choice-stability profile |
| − | 6 | + | 6 Config-Tilt -Sa -or 3 position switch of users choice-configuration/fan tilt |
| − | 7 | + | 7 Arming -Sd -optional-use this or other sw if arming switch will be configured) |
| − | 8 | + | 8 Mode Rates -Sc -optional-use if multi-rates will be implemented in BF for example) |
| − | 9 | + | 9 R Slider -P5 -optional-not currently used-drives spare servo port on FLEXF3) |
| − | 10 | + | 10 L Slider -P6 -optional-not currently used-drives spare servo port on FLEXF3) |
| − | </pre><big>'''NOTE:''' do | + | </pre><big>'''NOTE:''' '''''do NOT''''' hit the Auto-Assign button!</big> |
<br /> | <br /> | ||
''<big>Model->Servo Assignment</big>'' | ''<big>Model->Servo Assignment</big>'' | ||
| − | <br />Sets output order to same as Spektrum: Links the above functions to ‘output slots’ in data stream | + | <br /> |
| + | :Sets output order to same as Spektrum: Links the above functions to ‘output slots’ in data stream | ||
<pre> | <pre> | ||
1 Throttle | 1 Throttle | ||
| Line 74: | Line 83: | ||
</pre><br /> | </pre><br /> | ||
''<big>Model->Servo Setup</big>'' | ''<big>Model->Servo Setup</big>'' | ||
| + | [[File:BF_RX_Notes.png|thumb|upright=0.42|right|Betaflight Travel Tune Notes]] | ||
<pre> | <pre> | ||
All items set to defaults except as noted | All items set to defaults except as noted | ||
| − | ALL subtrims 0% | + | ALL subtrims 0% (defaults) |
| − | Travels | + | |
| − | All Max Positive 100% except for the Config/Tilt noted below (defaults) | + | Travels -general |
| − | All Max Negative -100% except for the Config/Tilt noted below (defaults) | + | All Max Positive 100% -except for the Config/Tilt noted below (defaults) |
| − | Travel for Config/Tilt | + | All Max Negative -100% -except for the Config/Tilt noted below (defaults) |
| − | + | Travel for Config/Tilt | |
| − | Max Negative | + | Max Positive 81% -start with these and then you MUST adjust final angle w/gauges |
| − | Reversing | + | Max Negative -57% |
| − | 1 NO | + | |
| − | 2 NO | + | Reversing 1-10 in Servo Assignment order as just above |
| − | 3 NO | + | 1 NO ‡ Normal is “Reverse NO”, Reverse is “Reverse YES” |
| − | 4 NO | + | 2 NO ‡ |
| − | 5 YES † | + | 3 NO ‡ |
| − | 6 NO | + | 4 NO ‡ |
| + | 5 YES † Or as user prefers for Stability/ANGLE MODE | ||
| + | 6 NO § Or as user prefers for Configuration/Fan Tilt | ||
7 NO † | 7 NO † | ||
8 NO † | 8 NO † | ||
9 NO † | 9 NO † | ||
10 NO † | 10 NO † | ||
| − | + | </pre> | |
| − | + | :'''NOTE:'''† User can set items 5-10 per their preference | |
| − | <br /> | + | :'''NOTE:'''‡ You must check Aileron, Elevator, Rudder 'Reversing' by rotating the virtual 'body' on the Receiver Page of the Configurator |
| + | :'''NOTE:'''§ The internal Flex pilots set the CH6 switch UP/Back for forward flight and Low/Front for Hover. You can set per your preference. | ||
| + | :'''Do the command and gyro checks in the manual''' | ||
| + | <br /><br /> | ||
''<big>Model->Timers/Sensors</big>'' | ''<big>Model->Timers/Sensors</big>'' | ||
<pre> | <pre> | ||
| Line 102: | Line 117: | ||
Timer length suggestion for first flights | Timer length suggestion for first flights | ||
2200mAh: 2:30 | 2200mAh: 2:30 | ||
| − | 2600mAh: 3: | + | 2600mAh: 3:00 |
| − | 3300mAh: | + | 3300mAh: 3:40 |
Other settings for telemetry/Alarms can be introduced in Wiki | Other settings for telemetry/Alarms can be introduced in Wiki | ||
</pre><br /> | </pre><br /> | ||
| Line 128: | Line 143: | ||
https://www.rcgroups.com/forums/showpost.php?p=33054194&postcount=8 | https://www.rcgroups.com/forums/showpost.php?p=33054194&postcount=8 | ||
| + | <br /><br /> | ||
| + | [[Cypher|Cypher Wiki Main]] | ||
Latest revision as of 16:36, 10 September 2019
Contents
Setup for using a Jeti Tx/Rx
Always start with a reset/new transmitter model!
- NOTE: You will use the 3-Pin to 4-Pin Male to Male cable provided to connect the Jeti Rx to the FLEXF3. This is the same cable arrangement shown on page 15 of the manual for the Futaba connections. (Non-Telemetry)
- These instructions supplement the printed manual. Please read the manual before proceeding.
CYPHER/Betaflight Settings
Use one of the Betaflight configuration tools to make these settings. Be sure to SAVE the page after adjustments.
Configuration Page
Receiver Mode -> Serial Based Receiver (Cypher Default)
Serial Receiver Provider -> JETIEXBUS
Telemetry slider -> OFF (Cypher Default - Unless configuring with telemetry
based using the other supplementary instructions)
- SAVE the Page
Receiver Page
Channel Order -> TAER1234 (Cypher Default - Same order as Spektrum)
- SAVE the Page
JETI Transmitter settings:
- DS-16 Mode 2 transmitter and R3 EX RSW Receiver used for validations
- (Most common models expected to work the SAME)
- As always, start with a freshly RESET transmitter model.
- You can verify the completed settings using the tools using the BetaFlight Configurator Receiver page.
Model->New Model
Name: FV-31 Cypher Model Type: Aero
- Bind to Rx per Jeti instructions (verify function with servo in port 2 if desired)
Model->Basic Properties
Name: FV-31 Cypher Wing type: 0 Flaps, 1 Ail Tail type: Normal 1H1V (default) Engine count: 1 (default) The rest are defaults (default)
Model->Functions Assignment
1 Ailerons -control P1 -(default) 2 Elevator -control P2 -(default) 3 Rudder -control P3 -(default) 4 Throttle -control P4 -(default) 5 Profile-Stabil -Sb -or 2 position switch of users choice-stability profile 6 Config-Tilt -Sa -or 3 position switch of users choice-configuration/fan tilt 7 Arming -Sd -optional-use this or other sw if arming switch will be configured) 8 Mode Rates -Sc -optional-use if multi-rates will be implemented in BF for example) 9 R Slider -P5 -optional-not currently used-drives spare servo port on FLEXF3) 10 L Slider -P6 -optional-not currently used-drives spare servo port on FLEXF3)NOTE: do NOT hit the Auto-Assign button!
Model->Servo Assignment
- Sets output order to same as Spektrum: Links the above functions to ‘output slots’ in data stream
1 Throttle 2 Aileron 3 Elevator 4 Rudder 5 Profile-Stab (Angle Mode / Stability 3 -vs- 6 axis) 6 Config-Tilt (Fan Tilt / Configuration switch) 7 Arming (Optional) 8 Mode Rates (Optional 9 R Slider (Optional) 10 L Slider (Optional)
Model->Servo Setup
All items set to defaults except as noted ALL subtrims 0% (defaults) Travels -general All Max Positive 100% -except for the Config/Tilt noted below (defaults) All Max Negative -100% -except for the Config/Tilt noted below (defaults) Travel for Config/Tilt Max Positive 81% -start with these and then you MUST adjust final angle w/gauges Max Negative -57% Reversing 1-10 in Servo Assignment order as just above 1 NO ‡ Normal is “Reverse NO”, Reverse is “Reverse YES” 2 NO ‡ 3 NO ‡ 4 NO ‡ 5 YES † Or as user prefers for Stability/ANGLE MODE 6 NO § Or as user prefers for Configuration/Fan Tilt 7 NO † 8 NO † 9 NO † 10 NO †
- NOTE:† User can set items 5-10 per their preference
- NOTE:‡ You must check Aileron, Elevator, Rudder 'Reversing' by rotating the virtual 'body' on the Receiver Page of the Configurator
- NOTE:§ The internal Flex pilots set the CH6 switch UP/Back for forward flight and Low/Front for Hover. You can set per your preference.
- Do the command and gyro checks in the manual
Model->Timers/Sensors
Timers: Set a free running
Timer length suggestion for first flights
2200mAh: 2:30
2600mAh: 3:00
3300mAh: 3:40
Other settings for telemetry/Alarms can be introduced in Wiki
Model->Device Explorer
With system powered and bound
Under Receiver Example: R3 EX with ‘Check Mark’
Serial Link: EX Bus
Note the JETIBOX/EX Bus Pin “Value” for plugging in Male to Male Cable.
On the R3-EX it is “Ext” which is marked “4/EXT” on the receiver.
The rest of settings are defaults/or as user desires
Note: Output period shows 17ms
Some third party links on using Jeti with Betaflight:
https://github.com/betaflight/betaflight/issues/167
https://github.com/betaflight/betaflight/blob/master/docs/Telemetry.md
https://www.drone-zone.de/anleitung-jeti-ex-telemetrie-mit-betaflight/
https://www.rcgroups.com/forums/showthread.php?2530376-Multirotor-Controller-Setup
https://www.rcgroups.com/forums/showpost.php?p=33054194&postcount=8
Cypher Wiki Main
