Difference between revisions of "Cypher/JetiInput"

Revision as of 21:11, 9 August 2019

Setup for using a Jeti Tx/Rx

Always start with a reset/new transmitter model!

Cypher/Betaflight Settings

Configuration Page

Receiver Mode             ->    Serial Based Receiver  (Cypher Default)
Serial Receiver Provide   ->    JETIEXBUS
Telemetry slider          ->    OFF                    (Cypher Default - Unless configuring with telemetry based
                                                        on those supplementary instructions)

Receiver Page

Channel Order             ->    TAER1234               (Cypher Default - Same as Spektrum)

Transmitter settings:

DS-16 transmitter and R3 EX RSW Receiver used for validations (Most common models expected to work the SAME)

Model->New Model

Name:                  FV-31 Cypher
Model Type:            Aero

Bind to Rx per Jeti instructions (verify function with servo in port 2 if desired)

Model->Basic Properties

Name:                  FV-31 Cypher
Wing type:             0 Flaps, 1 Ail
Tail type:             Normal 1H1V        (default)
Engine count:          1                  (default)
The rest are defaults                     (default)

Model->Functions Assignment

1    Ailerons         -control P1      -(default)
2    Elevator         -control P2      -(default)
3    Rudder           -control P3      -(default)
4    Throttle         -control P4      -(default)
5    Profile-Stabil   -Sb              -or 2 position switch of users choice for stability profile
6    Config-Tilt      -Sa              -or 3 position switch of users choice for configuration / fan tilt
7    Arming           -Sd              (totally optional -use this of other switch if arming switch will be configured later)
8    Mode Rates       -Sc              (totally optional -use if multi-rates will be implemented in BF for example)
9    R Slider          P5              (totally optional -not currently used but drives spare servo port on FLEXF3)
10   L Slider          P6              (totally optional -not currently used but drives spare servo port on FLEXF3)

Note: do not hit the Auto assign button!

Model->Servo Assignment
Sets output order to same as Spektrum: Links the above functions to ‘output slots’ in data stream

1    Throttle
2    Aileron
3    Elevator
4    Rudder
5    Profile-Stab      (Angle Mode / Stability 3 -vs- 6 axis)
6    Config-Tilt       (Fan Tilt / Configuration switch)
7    Arming            (Optional)
8    Mode Rates        (Optional
9    R Slider          (Optional)
10   L Slider          (Optional)

Model->Servo Setup

All items set to defaults except as noted
ALL subtrims 0%                  (defaults)
Travels                          (General)
   All Max Positive are   100%   except for the Config/Tilt noted below     (defaults)
   All Max Negative are  -100%   except for the Config/Tilt noted below     (defaults)
Travel for Config/Tilt           (start with these and '''MUST''' adjust with gauges)
   Max Positive           81%  
   Max Negative          -57%
Reversing                        (1-10 in Servo Assignment order as just above)
   1  NO                         (Normal is “Reverse NO”, Reverse is “Reverse YES”)
   2  NO
   3  NO
   4  NO
   5  YES †     
   6  NO  †
   7  NO  †
   8  NO  †
   9  NO  †
   10 NO  †
†User can set items 5-10 per their preference

Do the command and gyro checks

Model->Timers/Sensors

Timers:    Set a free running
Timer length suggestion for first flights
     2200mAh:            2:30
     2600mAh:            3:10
     3300mAh:            4:00
Other settings for telemetry/Alarms can be introduced in Wiki

Model->Device Explorer

With system powered and bound
  Under Receiver         (ex. R3 EX with ‘Check Mark’)
     Serial Link:         EX Bus
     Note the JETIBOX/EX Bus Pin “Value” for plugging in Male to Male Cable.
     On the R3-EX it is “Ext” which is marked “4/EXT” on the receiver.
     The rest of settings are defaults/or as user desires
Note: Output period shows 17ms