Difference between revisions of "Cypher/JetiInput"
(→Transmitter settings:) |
(→Transmitter settings:) |
||
Line 74: | Line 74: | ||
All Max Positive are 100% except for the Config/Tilt noted below (defaults) | All Max Positive are 100% except for the Config/Tilt noted below (defaults) | ||
All Max Negative are -100% except for the Config/Tilt noted below (defaults) | All Max Negative are -100% except for the Config/Tilt noted below (defaults) | ||
− | Travel for Config/Tilt (start with these and | + | Travel for Config/Tilt (start with these and then you MUST adjust final angle with gauges) |
Max Positive 81% | Max Positive 81% | ||
Max Negative -57% | Max Negative -57% |
Revision as of 21:16, 9 August 2019
Contents
Setup for using a Jeti Tx/Rx
Always start with a reset/new transmitter model!
Cypher/Betaflight Settings
Configuration Page
Receiver Mode -> Serial Based Receiver (Cypher Default) Serial Receiver Provide -> JETIEXBUS Telemetry slider -> OFF (Cypher Default - Unless configuring with telemetry based on those supplementary instructions)
Receiver Page
Channel Order -> TAER1234 (Cypher Default - Same as Spektrum)
Transmitter settings:
DS-16 transmitter and R3 EX RSW Receiver used for validations
(Most common models expected to work the SAME)
Model->New Model
Name: FV-31 Cypher Model Type: Aero
Bind to Rx per Jeti instructions (verify function with servo in port 2 if desired)
Model->Basic Properties
Name: FV-31 Cypher Wing type: 0 Flaps, 1 Ail Tail type: Normal 1H1V (default) Engine count: 1 (default) The rest are defaults (default)
Model->Functions Assignment
1 Ailerons -control P1 -(default) 2 Elevator -control P2 -(default) 3 Rudder -control P3 -(default) 4 Throttle -control P4 -(default) 5 Profile-Stabil -Sb -or 2 position switch of users choice for stability profile 6 Config-Tilt -Sa -or 3 position switch of users choice for configuration / fan tilt 7 Arming -Sd (totally optional -use this of other switch if arming switch will be configured later) 8 Mode Rates -Sc (totally optional -use if multi-rates will be implemented in BF for example) 9 R Slider P5 (totally optional -not currently used but drives spare servo port on FLEXF3) 10 L Slider P6 (totally optional -not currently used but drives spare servo port on FLEXF3)Note: do not hit the Auto assign button!
Model->Servo Assignment
Sets output order to same as Spektrum: Links the above functions to ‘output slots’ in data stream
1 Throttle 2 Aileron 3 Elevator 4 Rudder 5 Profile-Stab (Angle Mode / Stability 3 -vs- 6 axis) 6 Config-Tilt (Fan Tilt / Configuration switch) 7 Arming (Optional) 8 Mode Rates (Optional 9 R Slider (Optional) 10 L Slider (Optional)
Model->Servo Setup
All items set to defaults except as noted ALL subtrims 0% (defaults) Travels (General) All Max Positive are 100% except for the Config/Tilt noted below (defaults) All Max Negative are -100% except for the Config/Tilt noted below (defaults) Travel for Config/Tilt (start with these and then you MUST adjust final angle with gauges) Max Positive 81% Max Negative -57% Reversing (1-10 in Servo Assignment order as just above) 1 NO (Normal is “Reverse NO”, Reverse is “Reverse YES”) 2 NO 3 NO 4 NO 5 YES † 6 NO † 7 NO † 8 NO † 9 NO † 10 NO † †User can set items 5-10 per their preferenceDo the command and gyro checks
Model->Timers/Sensors
Timers: Set a free running Timer length suggestion for first flights 2200mAh: 2:30 2600mAh: 3:10 3300mAh: 4:00 Other settings for telemetry/Alarms can be introduced in Wiki
Model->Device Explorer
With system powered and bound Under Receiver Example: R3 EX with ‘Check Mark’ Serial Link: EX Bus Note the JETIBOX/EX Bus Pin “Value” for plugging in Male to Male Cable. On the R3-EX it is “Ext” which is marked “4/EXT” on the receiver. The rest of settings are defaults/or as user desires Note: Output period shows 17ms
Some third party links on using Jeti with Betaflight:
https://github.com/betaflight/betaflight/issues/167
https://github.com/betaflight/betaflight/blob/master/docs/Telemetry.md
https://www.drone-zone.de/anleitung-jeti-ex-telemetrie-mit-betaflight/
https://www.rcgroups.com/forums/showthread.php?2530376-Multirotor-Controller-Setup
https://www.rcgroups.com/forums/showpost.php?p=33054194&postcount=8