Difference between revisions of "Cypher/JetiInput"
(→JETI Transmitter settings:) |
(→JETI Transmitter settings:) |
||
Line 51: | Line 51: | ||
3 Rudder -control P3 -(default) | 3 Rudder -control P3 -(default) | ||
4 Throttle -control P4 -(default) | 4 Throttle -control P4 -(default) | ||
− | 5 Profile-Stabil -Sb | + | 5 Profile-Stabil -Sb -or 2 position switch of users choice-stability profile |
− | 6 Config-Tilt -Sa | + | 6 Config-Tilt -Sa -or 3 position switch of users choice-configuration/fan tilt |
− | 7 Arming -Sd | + | 7 Arming -Sd -optional-use this of other switch if arming switch will be configured) |
− | 8 Mode Rates -Sc | + | 8 Mode Rates -Sc -optional-use if multi-rates will be implemented in BF for example) |
− | 9 R Slider -P5 | + | 9 R Slider -P5 -optional-not currently used-drives spare servo port on FLEXF3) |
− | 10 L Slider -P6 | + | 10 L Slider -P6 -optional-not currently used-drives spare servo port on FLEXF3) |
</pre><big>'''NOTE:''' do not hit the Auto-Assign button!</big> | </pre><big>'''NOTE:''' do not hit the Auto-Assign button!</big> | ||
<br /> | <br /> |
Revision as of 16:39, 10 August 2019
Contents
Setup for using a Jeti Tx/Rx
Always start with a reset/new transmitter model!
NOTE: You will use the 3-Pin to 4-Pin Male to Male cable provided to connect the Jeti Rx to the FLEXF3. This is the same cable arrangement shown on page 15 of the manual for the Futaba connections. (Non-Telemetry)
CYPHER/Betaflight Settings
Use one of the Betaflight configuration tools to make these settings. Be sure to SAVE the page after adjustments.
Configuration Page
Receiver Mode -> Serial Based Receiver (Cypher Default) Serial Receiver Provider -> JETIEXBUS Telemetry slider -> OFF (Cypher Default - Unless configuring with telemetry based using the other supplementary instructions)
Receiver Page
Channel Order -> TAER1234 (Cypher Default - Same order as Spektrum)
JETI Transmitter settings:
DS-16 Mode 2 transmitter and R3 EX RSW Receiver used for validations
(Most common models expected to work the SAME)
You can verify the completed settings using the tools using the BetaFlight Receiver page.
Model->New Model
Name: FV-31 Cypher Model Type: Aero
Bind to Rx per Jeti instructions (verify function with servo in port 2 if desired)
Model->Basic Properties
Name: FV-31 Cypher Wing type: 0 Flaps, 1 Ail Tail type: Normal 1H1V (default) Engine count: 1 (default) The rest are defaults (default)
Model->Functions Assignment
1 Ailerons -control P1 -(default) 2 Elevator -control P2 -(default) 3 Rudder -control P3 -(default) 4 Throttle -control P4 -(default) 5 Profile-Stabil -Sb -or 2 position switch of users choice-stability profile 6 Config-Tilt -Sa -or 3 position switch of users choice-configuration/fan tilt 7 Arming -Sd -optional-use this of other switch if arming switch will be configured) 8 Mode Rates -Sc -optional-use if multi-rates will be implemented in BF for example) 9 R Slider -P5 -optional-not currently used-drives spare servo port on FLEXF3) 10 L Slider -P6 -optional-not currently used-drives spare servo port on FLEXF3)NOTE: do not hit the Auto-Assign button!
Model->Servo Assignment
Sets output order to same as Spektrum: Links the above functions to ‘output slots’ in data stream
1 Throttle 2 Aileron 3 Elevator 4 Rudder 5 Profile-Stab (Angle Mode / Stability 3 -vs- 6 axis) 6 Config-Tilt (Fan Tilt / Configuration switch) 7 Arming (Optional) 8 Mode Rates (Optional 9 R Slider (Optional) 10 L Slider (Optional)
Model->Servo Setup
All items set to defaults except as noted ALL subtrims 0% (defaults) Travels (General) All Max Positive 100% except for the Config/Tilt noted below (defaults) All Max Negative -100% except for the Config/Tilt noted below (defaults) Travel for Config/Tilt (start with these and then you MUST adjust final angle with gauges) Max Positive 81% Max Negative -57% Reversing (1-10 in Servo Assignment order as just above) 1 NO (Normal is “Reverse NO”, Reverse is “Reverse YES”) 2 NO 3 NO 4 NO 5 YES † 6 NO † 7 NO † 8 NO † 9 NO † 10 NO † †User can set items 5-10 per their preferenceDo the command and gyro checks
Model->Timers/Sensors
Timers: Set a free running Timer length suggestion for first flights 2200mAh: 2:30 2600mAh: 3:10 3300mAh: 4:00 Other settings for telemetry/Alarms can be introduced in Wiki
Model->Device Explorer
With system powered and bound Under Receiver Example: R3 EX with ‘Check Mark’ Serial Link: EX Bus Note the JETIBOX/EX Bus Pin “Value” for plugging in Male to Male Cable. On the R3-EX it is “Ext” which is marked “4/EXT” on the receiver. The rest of settings are defaults/or as user desires Note: Output period shows 17ms
Some third party links on using Jeti with Betaflight:
https://github.com/betaflight/betaflight/issues/167
https://github.com/betaflight/betaflight/blob/master/docs/Telemetry.md
https://www.drone-zone.de/anleitung-jeti-ex-telemetrie-mit-betaflight/
https://www.rcgroups.com/forums/showthread.php?2530376-Multirotor-Controller-Setup
https://www.rcgroups.com/forums/showpost.php?p=33054194&postcount=8