Cypher/JetiInput

Setup for using a Jeti Tx/Rx

Always start with a reset/new transmitter model!

Cypher/Betaflight Settings

Configuration Page

Receiver Mode -> Serial Based Receiver (Cypher Default)
Serial Receiver Provide -> JETIEXBUS
Telemetry slider is OFF (Cypher Default - Unless configuring with telemetry based on those supplementary instructions)

Receiver Page

Channel Order -> TAER1234 (Cypher Default - Same as Spektrum)

Some text      aligned
Next           aligned
Test           yep           next

Transmitter settings:

DS-16 transmitter and R3 EX RSW Receiver used for validations (Most common models expected to work the SAME)

Model->New Model

Name: FV-31 Cypher
Model Type: Aero

Bind to Rx per Jeti instructions (verify function with servo in port 2 if desired)

Model->Basic Properties

Name: FV-31 Cypher
Wing type: 0 Flaps, 1 Ail
Tail type: Normal 1H1V (default)
Engine count: 1 (default)
The rest are defaults (default)

Model->Functions Assignment

*1 Ailerons    -control P1                  -(default)
*2 Elevator    -control P2                  -(default)
*3 Rudder      -control P3                  -(default)
*4 Throttle    -control P4                  -(default)
*5 Profile-Stabil    -Sb -or 2 position switch of users choice for stability profile
*6 Config-Tilt       -Sa -or 3 position switch of users choice for configuration / fan tilt
*7 Arming            -Sd            (totally optional -use this of other switch if arming switch will be configured later)
*8 Mode Rates        -Sc            (totally optional -use if multi-rates will be implemented in BF for example)
*9 R Slider           P5            (totally optional -not currently used but drives spare servo port on FLEXF3)
*10 L Slider          P6            (totally optional -not currently used but drives spare servo port on FLEXF3)

Note: do not hit the Auto assign button!

Model->Servo Assignment

Model->Functions Assignment

1 Ailerons -control P1 -(default)
2 Elevator -control P2 -(default)
3 Rudder -control P3 -(default)
4 Throttle -control P4 -(default)
5 Profile-Stabil -Sb -or 2 position switch of users choice for stability profile
6 Config-Tilt -Sa -or 3 position switch of users choice for configuration / fan tilt
7 Arming -Sd (totally optional -use this of other switch if arming switch will be configured later)
8 Mode Rates -Sc (totally optional -use if multi-rates will be implemented in BF for example)
9 R Slider P5 (totally optional -not currently used but drives spare servo port on FLEXF3)
10 L Slider P6 (totally optional -not currently used but drives spare servo port on FLEXF3)

Note: do not hit the Auto assign button!

Model->Servo Assignment
(sets output order… to same as Spektrum: Links the above functions to ‘output slots’ in data stream)

1 Throttle
2 Aileron
3 Elevator
4 Rudder
5 Profile-Stab (Angle Mode / Stability 3 -vs- 6 axis)
6 Config-Tilt (Fan Tilt / Configuration switch)
7 Arming (Optional)
8 Mode Rates (Optional
9 R Slider (Optional)
10 L Slider (Optional)

Model->Servo Setup

All items set to defaults except as noted
ALL subtrims 0% (defaults)
Travels
- All Max Positive are 100% except for the Config/Tilt noted below (defaults) (Travels)
- All Max Negative are -100% except for the Config/Tilt noted below (defaults) (Travels)
- Config/Tilt Travel (start here and MUST adjust with gauges)
  - Max Positive 81% (travel)
  - Max Negative -57%
Reversing (1-10 in Servo Assignment order as just above) (Normal is “Reverse NO”, Reverse is “Reverse YES”)
- 1 NO (normal)
- 2 NO
- 3 NO
- 4 NO
- 5 YES † (reversed)
- 6 NO †
- 7 NO †
- 8 NO †
- 9 NO †
- 10 NO †

†User can change per preference
(Do the command and gyro checks)

Model->Timers/Sensors

Timers: Set a free running
Time suggestion for first flights
- 2200mAh: 2:30
- 2600mAh: 3:10
- 3300mAh: 4:00

Other settings for telemetry/Alarms can be introduced in Wiki

Model->Device Explorer
(with system powered and bound)

Under Receiver (ex. R3 EX with ‘Check Mark’)
- Serial Link: EX Bus
- Note the JETIBOX/EX Bus Pin: “Value” for plugging in Male to Male Cable On the R3-EX it is “Ext” which is marked “4/EXT” on the receiver.
- Rest of settings are defaults/or as user desires

(Note: Output period shows 17ms)