Difference between revisions of "Ventique60e/BuildTips"
From Flex Innovations Wiki
| (24 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
| − | {{DISPLAYTITLE:Ventique 60e Build Tips}} | + | {{DISPLAYTITLE:Ventique 60e Build Tips and Aura Install}} |
| − | *[http:// | + | *Please review [http://www.resources.flexinnovations.com/files/9712370-_Ventique_Addendum.pdf '''Ventique Addendum'''] with Building tips. |
| − | * | + | *There have been a couple of reports of the '''set screws coming loose''' in the Potenza 60 470kv Motor. During the build, please remove the shaft set screws one at a time from the bell housing (flange) and the shaft retaining collar, apply 242 loctite, and tighten them securely. Motor instructions with images can be [http://www.resources.flexinnovations.com/files/Potenza_60_Instructions_ENG.pdf '''seen here'''] |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | [[File:Ventique Aura 600h.png|upright=. | + | *Ventique '''Aura Installation Instructions'''[[File:Ventique Aura 600h.png|thumb|upright=0.5|right|Reinforce the Tray]] |
| + | **Mount the Aura oriented as shown on the Platform behind the wing tube with two-sided tape and secure with a hook-and-loop strap. | ||
| + | **Fabricate a plywood or balsa diagonal brace from the platform to the former near the floor to stiffen the mounting platform, otherwise, you will have significant vibration feedback into the gyro sensors. | ||
| + | **The Aura Config File for the Ventique can be easily built in the ''New Aura Config File'' "Wizard" by selecting the "Aura Config Type: Ventique", and then choosing the other details of your setup in the Wizard. | ||
| + | ***Alternately, you can [[Aura/ConfigFiles#Ventique_60e_Aura_Config_Files_with_Rx_Auto_Detect| Download a Ventique .acf file]] | ||
| + | **After you setup is complete, secure the Aura with a hook-and-loop strap | ||
| − | * | + | *'''Ventique Manual''' in [http://store.flexinnovations.com/s/Ventique_60e_Assembly_Manual_English.pdf '''English'''] and [http://store.flexinnovations.com/s/9712370_German_Manual_V2.PDF '''German'''] |
| − | + | *When using the new '''"T" Spektrum Receivers''' such as the AR8010T, the Aura '''MUST be updated''' via Aura Config Tool to '''Firmware 1.4''' to establish connection via SRXL as noted on our AR8010T page. | |
| − | + | <br /> | |
| − | [[ | + | <noinclude> |
| + | [[Category:ARF+ARFSV|ARF + ARFSV]] | ||
| + | [[Category:Ventique60e|Ventique 60e]] | ||
| + | </noinclude> | ||
Latest revision as of 20:53, 29 November 2017
- Please review Ventique Addendum with Building tips.
- There have been a couple of reports of the set screws coming loose in the Potenza 60 470kv Motor. During the build, please remove the shaft set screws one at a time from the bell housing (flange) and the shaft retaining collar, apply 242 loctite, and tighten them securely. Motor instructions with images can be seen here
- Ventique Aura Installation Instructions
- Mount the Aura oriented as shown on the Platform behind the wing tube with two-sided tape and secure with a hook-and-loop strap.
- Fabricate a plywood or balsa diagonal brace from the platform to the former near the floor to stiffen the mounting platform, otherwise, you will have significant vibration feedback into the gyro sensors.
- The Aura Config File for the Ventique can be easily built in the New Aura Config File "Wizard" by selecting the "Aura Config Type: Ventique", and then choosing the other details of your setup in the Wizard.
- Alternately, you can Download a Ventique .acf file
- After you setup is complete, secure the Aura with a hook-and-loop strap
- Ventique Manual in English and German
- When using the new "T" Spektrum Receivers such as the AR8010T, the Aura MUST be updated via Aura Config Tool to Firmware 1.4 to establish connection via SRXL as noted on our AR8010T page.
