Difference between revisions of "F-100D 90mm EDF/LatestUpdates"
From Flex Innovations Wiki
(→Spektrum SRXL2 Use) |
|||
(30 intermediate revisions by the same user not shown) | |||
Line 3: | Line 3: | ||
== Latest Updates == | == Latest Updates == | ||
=== Latest Online Manual === | === Latest Online Manual === | ||
− | The Latest Version of the [http://www.resources.flexinnovations.com/Flex_Images/PDF_Library/F-100D%20Super%20Sabre%20manual_SPNP_R1.pdf F-100D Manual] is available online.[[Image:F-100_CG.JPG||thumb|300px|right|Proper F-100D CG Locations]] | + | The Latest Version of the [http://www.resources.flexinnovations.com/Flex_Images/PDF_Library/F-100D%20Super%20Sabre%20manual_SPNP_R1.pdf '''F-100D Manual'''] is available online.[[Image:F-100_CG.JPG||thumb|300px|right|Proper F-100D CG Locations]] |
* This version matches the printed manual. | * This version matches the printed manual. | ||
− | === Addendums === | + | === Addendums and Additional Info=== |
====Center of Gravity==== | ====Center of Gravity==== | ||
*The CG section of the F-100D manual had some conflicting information displayed. The correct CG's are listed in the image to the right. Click for the full sized image. | *The CG section of the F-100D manual had some conflicting information displayed. The correct CG's are listed in the image to the right. Click for the full sized image. | ||
+ | ====ESC Wires==== | ||
+ | *Check that the 3 ESC/Motor wires are fully plugged in before installing the Fin. | ||
+ | *We recommend securing them with heat shrink or electrical tape to remove any chance they could be pulled loose. | ||
+ | |||
+ | ====Care Tips==== | ||
+ | *As with all foam planes, and especially those with dark colors and cockpits, keep your plane out of direct sunlight (or cover it) when not flying! | ||
+ | *TIP: You can use a small drill bit or a #11 knife blade to make a small 2-3mm hole in the clear canopy above the ejection seat. This will reduce the temperatures a bit in the cockpit due to the 'greenhouse effect'. Hot cars and direct Sun are also bad for the finish. | ||
+ | *Use foam, a soft stand, or towels, or similar items to protect your models surface and finish when working on it, or transporting it! | ||
+ | |||
+ | ====JR DMSS Use==== | ||
+ | *In addition to the JR DMSS receivers listed in the manual, the '''RG812BX''' should be a good choice as well. Avoid the '''BPX''' receivers as they will not do servo pulses and serial data at the same time. | ||
+ | *We recommend updating to the very latest Aura Firmware '''v1.14''' or higher and then set the 'new to Aura' '''JR XBUS MODE A''' serial data in the transmitter and the Aura. | ||
+ | *Using '''MODE A''', you can physically wire/connect it just like Futaba diagram in the manual (P. 7). Throttle and Gear in the Receivers ports. Xbus to Port B in Aura. | ||
+ | *More information can be found in the [[Aura#Radio_Brand_Tips_-_for_all_Auras| '''Aura Brand Tips''']] | ||
+ | ====Jeti EX Bus Use==== | ||
+ | *Note that EX Bus is now the preferred Jeti connection with Aura. More information can be found in the [[Aura#Radio_Brand_Tips_-_for_all_Auras| '''Aura Brand Tips''']] | ||
+ | |||
+ | ====Spektrum SRXL2 Use==== | ||
+ | *Note that the AR6610T using SRXL2 is working with the Aura and F-100D. More information can be found in the [[Aura#Radio_Brand_Tips_-_for_all_Auras| '''Aura Brand Tips''']] | ||
== Build Tips == | == Build Tips == | ||
+ | *The Drop Tanks are fully assembled, no need to assemble the fins onto the tanks. | ||
+ | [[F-100D_90mm_EDF| '''CLICK HERE to go back to the main F-100D Wiki Page''']] | ||
<noinclude> | <noinclude> |
Latest revision as of 14:03, 28 September 2020
Contents
Latest Updates
Latest Online Manual
The Latest Version of the F-100D Manual is available online.- This version matches the printed manual.
Addendums and Additional Info
Center of Gravity
- The CG section of the F-100D manual had some conflicting information displayed. The correct CG's are listed in the image to the right. Click for the full sized image.
ESC Wires
- Check that the 3 ESC/Motor wires are fully plugged in before installing the Fin.
- We recommend securing them with heat shrink or electrical tape to remove any chance they could be pulled loose.
Care Tips
- As with all foam planes, and especially those with dark colors and cockpits, keep your plane out of direct sunlight (or cover it) when not flying!
- TIP: You can use a small drill bit or a #11 knife blade to make a small 2-3mm hole in the clear canopy above the ejection seat. This will reduce the temperatures a bit in the cockpit due to the 'greenhouse effect'. Hot cars and direct Sun are also bad for the finish.
- Use foam, a soft stand, or towels, or similar items to protect your models surface and finish when working on it, or transporting it!
JR DMSS Use
- In addition to the JR DMSS receivers listed in the manual, the RG812BX should be a good choice as well. Avoid the BPX receivers as they will not do servo pulses and serial data at the same time.
- We recommend updating to the very latest Aura Firmware v1.14 or higher and then set the 'new to Aura' JR XBUS MODE A serial data in the transmitter and the Aura.
- Using MODE A, you can physically wire/connect it just like Futaba diagram in the manual (P. 7). Throttle and Gear in the Receivers ports. Xbus to Port B in Aura.
- More information can be found in the Aura Brand Tips
Jeti EX Bus Use
- Note that EX Bus is now the preferred Jeti connection with Aura. More information can be found in the Aura Brand Tips
Spektrum SRXL2 Use
- Note that the AR6610T using SRXL2 is working with the Aura and F-100D. More information can be found in the Aura Brand Tips
Build Tips
- The Drop Tanks are fully assembled, no need to assemble the fins onto the tanks.